MEDP585GW0 Maytag Dryer - Overview
Sections of the MEDP585GW0
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Dryer Repair Kit
PartSelect #: PS373088
Manufacturer #: 4392067
This dryer repair kit consists of five commonly replaced dryer parts: one multi-rib belt (part #661570V and measures 93 1/2 inches long), four drum support rollers, one idler assembly, nine tri-rings,...
$60.74
In Stock
Door Catch Kit
PartSelect #: PS334230
Manufacturer #: 279570
This kit contains two door strikes, and three door catches to service dryer doors that have one or two catches.
$8.82
In Stock
Dryer Heating Element
PartSelect #: PS11741416
Manufacturer #: WP3387747
When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside ...
$82.61
In Stock
Dryer Drum Support Roller
PartSelect #: PS11752609
Manufacturer #: WPW10314173
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. This part is sold separ...
$23.96
In Stock
Lint Filter
PartSelect #: PS1491676
Manufacturer #: W10120998
This dryer lint filter is designed to capture lint and debris during the drying cycle, helping maintain airflow and prevent potential fire hazards. Measuring approximately 12.5 inches wide by 10.5 inc...
$67.65
In Stock
Moisture Sensor
PartSelect #: PS11741408
Manufacturer #: WP3387223
This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is do...
$13.59
In Stock
Roller Support Tri-Ring
PartSelect #: PS11755850
Manufacturer #: WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
$17.01
In Stock
High Limit Thermostat and Thermal Cut-Off Kit
PartSelect #: PS334387
Manufacturer #: 279973
Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than...
$67.53
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$15.95
In Stock
Dryer Drum Seal with Adhesive
PartSelect #: PS970088
Manufacturer #: 280114
This part seals the drum to prevents air from escaping. This includes silicone rubber adhesive.
$55.94
In Stock
Outlet Screen Door Grille
PartSelect #: PS12070617
Manufacturer #: W11086603
Protect your clothes and keep your dryer running smoothly with this replacement screen door grille. As the top cover for the lint filter, it helps prevent snags and supports proper airflow. If your cu...
$35.89
In Stock
Questions And Answers for MEDP585GW0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
April 9, 2024
Touched top of dryer and it shocked me, and now the machine does not work at all.
For model number MEDP585GW0
Hello James, thank you for the question. We would recommend replacing the terminal and wire kit, part number PS334181. This sounds like a case of the housing of the appliance was not properly grounded. If you have a multimeter, you can set it to AC volts, place one probe in a hot slot on the face of an outlet, and the other probe in the ground slot. If everything appears normal at the outlet, open the cover over the terminal screws on the back of the appliance where the cord connects to the unit. The green wire coming out of the cord should be bonded to the frame of the appliance. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Related Parts:
Terminal and Wire Kit
$86.15
Special Order
Nick
October 28, 2025
On the bottom of the dryer door, where the vent is, the thing that holds the vent in place has two sprints on the bottom. The bottom spring isn't able to hold in place, it's too loose. I tried melting it a bit and the bottom spring stayed but now it popped off again. What part do I replace?
For model number MEDP585GW0
Hi Nick, thank you for your inquiry. Based on your description, the part that needs to be replaced is a spring clip fastener, part number PS11744885. This is a small spring-tensioned clip that holds panels or parts in place inside the dryer door assembly. Glad to be of help!
Was this helpful?
Thank you for voting!
Related Parts:
Spring Clip
$12.62
In Stock
- < Prev
- 1
- Next >
Common Symptoms of the MEDP585GW0
[Viewing 15 of 15]Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Running With Door Open
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Door Pops Open
Fixed by
these parts
these parts
Show All
Timer Not Working
Fixed by
these parts
these parts
Show All
Light not working
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Fridge too warm
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
door switch was bad
i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service
Parts Used:
-
pat from lisbon,, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench set
1032 of 1091 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Catch part had fallen out,/ was missing
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.
Parts Used:
-
Terri from Saint Augustine, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
675 of 739 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer Would Not Turn Off With Door Open
Pryed dryer top open and opened front door. . Unscrewed the 2 retaining screws. Pulled old switch from the wiring harness. Put new switch in place and replaced the retaining screws. Put new switch wire plug into the wiring harness. Before closing top, checked door switch function with dryer on. Dryer cut off when door open and when closed dryer started normally. . . Maint. Note instruction book should warn that letting door slam, which I did on occaision, broke the switch arm. Might save future problems.
Parts Used:
-
RICHARD from NORCROSS, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
575 of 596 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!