This dryer drum belt from Amana has five ridges and is 93-3/8" inches in length, and 3/8 of an inch wide. It is flat, black in color, and is made entirely of rubber.
$12.04
In Stock
Order within the next 3 hrs and your part ships today!
The spring for this part is sold separately.
This idler assembly is for dryers.
Idler assembly includes the idler arm and the idler pulley that maintains tension on the drive belt, allowing the ...
$45.51
In Stock
Order within the next 3 hrs and your part ships today!
Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do...
$16.54
In Stock
Order within the next 3 hrs and your part ships today!
This dryer drum glide pad is an inch long. It is made of a felt material and is used for gas and electric clothes dryers.
$10.20
In Stock
Order within the next 3 hrs and your part ships today!
Questions And Answers for MDET236AYW
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
March 23, 2023
Yes my drum is not turning I found a piece of string from a hoodie had gone down past the lint trap I believe it has tangled itself around the drum could that be the cause and how do I remove it
For model number MDET236AYW
Hi Michael, thank you for contacting us. Yes, this might be the reason behind the drum not turning. To remove this tangled piece of string, the top and front panels of the washer need to be disassembled to get access to the drum. Once the panels are removed, the outer side of the drum will become visible, and you can remove the stuck piece of string. We have found a video to help you disassemble the panels. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Bob
February 24, 2020
Belt on drum loose like it is off motor.How do you find motor?
For model number MDET236AYW
Hi Bob,
Thank you for your question. Here is a link to one of our videos from YouTube that you may reference on how to access the dryer motor, https://www.youtube.com/watch?v=eXJMmn5mwMY. The dryer in the video may not show exactly like the one you have, but it will give you a general idea on how to access the part. We hope this helps. Thank you and have a great day.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Wayne
November 4, 2022
When I turn it on all I get is a humming sound. Tub does not turn. Belt not broken. Could it be the motor?
For model number MDET236AYW
Hello Wayne, thank you for contacting us. We would recommend checking the following parts to fix your issue: Drum Support Roller, part number PS11741913, Drum Glide, part number PS11741931, Idler Assembly, part number PS11741930, and Motor Assembly, part number PS11739459. If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
Hello Corbin, thank you for reaching out to PartSelect. The dryer timer, part number PS11741924, will fit your model. We look forward to hearing from you if you need assistance with placing an order through our 7-days-a-week customer service. We hope this helps!
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it.
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surfaces and let dry. I then applied a 2nd coat and let get "tacky" and installed the gasket. You will need an extra set of hands to hold the gasket in place while you stretch it over the the panel. The vent manifold is held in place with 3 phillips screws and was installed in about 10 minutes. The only gripe I had was in the Parts-Select illustrated breakdown they don't tell you the lint screen comes with the manifold assembly, so I bought one of them too. Now have an extra lint screen
Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to. Followed other people's excellent instructions. Clean out all the dust bunnies. Schematics were a great resource. Those and the prices made me a repeat customer. The shaft of the Idler Lever wheel was the cause, but decided, since I had it apart, to spend a little more money and replace both Drum Support Rollers and the Roller Bracket and Shaft Assembly. They showed some wear, and the parts were very inexpensive. Make sure you have snap ring pliers with prongs that are smaller than the standard 0.40 to save some aggravation with the Drum Rollers. $5 tool. Total parts were less than $60. Probably saved $150+ in labor. Quieter than ever now. Thanks!