This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
Sold individually. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward.
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
The heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher.
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
This part is used to hold the access panel in place. Sold individually.
$9.45
In Stock
Questions And Answers for MDB4949SDM3
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
March 3, 2023
my clean lite is on where is filter and how do I clean it
For model number MDB4949SDM3
Hi James, thank you for the question. Please follow these steps to clean the filters of the dishwasher.
1- Locate the filter at the bottom of the dishwasher.
2- Turn the upper filter assembly counterclockwise and lift it out.
3- Lift the lower filter and remove it from the circular opening.
4- Rinse the filter under running water.
5- Use a soft brush to scrub if necessary, but avoid using wire brushes or scouring pads.
6- Place the lower filter back under the locating tabs.
7- Insert the upper filter assembly into the circular opening and rotate clockwise until it drops into place.
8- Ensure the filter is locked securely into place before operating the dishwasher.
We hope this information helps!
Was this helpful?
Thank you for voting!
Tom
May 3, 2023
I replaced lower rack wheels and upper rack supports. .y upper spray arm is not rotating. Water is getting to it but perhaps not enough. Is there a gasket or seal that needs to be replaced on the upper rack.
For model number MDB4949SDM3
Hello Tom, thank you for the question. According to our research, you may need to check that the upper spray arm is not clogged. If the issue still persists, you may need to check the circulation pump, part number PS11723102, to fix the issue. We hope this helps!
Hi Lori, thank you for a very interesting question. The upper spray arm, part number PS11752935, and the lower spray arm, part number PS11722921, are compatible with your model. We hope this is what you were looking for!
The dishwasher will fill and drain but no pressure to wash. I've removed the base parts and cleaned them all. Did not help.
For model number MDB4949SDM3
Hi Tim,
Thank you for your question. If your dishwasher has no water pressure and you have cleaned the spray jets, you may have a float switch malfunction. If the float is damaged, it will turn the water off and the dishwasher will not fill. If there is a clog in the pump, this can cause a water pressure issue.
Check the pump to see if it is clogged and clean it. Also, make sure that you are not overloading the dishwasher. Overloading the dishwasher will make it difficult for the dishwasher to clean the dishes.
Check the water pressure in the home and inspect the water inlet valve for any cracks or leaks. If it shows any of these signs, replace it. We hope this helps! If you have any questions, please let us know.
Water doesn't spray and I can't hear the pump run!!!!
For model number MDB4949SDM3
Hi Duane,
Thank you for your question. If water is not spraying from the arms and you cannot hear the circulation pump, it may be clogged or malfunctioning and you will need to inspect it. If it does need to be replaced the part number listed under your model number for it is PS11723102. If you would like to place an order for it, please call our customer service line and anyone will be happy to assist you. We look forward to hearing from you!
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water input line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.