This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt encounter wear and tear.
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. NOTE: This is a redesigned part. The pump now mounts on to the b...
Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY availab...
This package contains a new set of six springs. The suspension springs in your washer connect to the bottom of tub, and help to hold it in place. If your washer tub shakes, or moves around a lot durin...
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
This water valve is for 60% hot water and 40% cold - This is done to save on energy.
$156.03
In Stock
Questions And Answers for MAVT236AWW
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Carol
May 2, 2023
Washer does not agitate nor spin proper. What could be problem. Pump still removes water
For model number MAVT236AWW
Hi Carol, thank you for reaching out. We have researched the model and would suggest checking the drive belt, part number PS11738882. The drive belt is made to slip on the motor pulley to bring the basket up to the required speed. This might make the belt encounter wear and tear. We hope this information helps!
does this model have any sort of neutral drain or is it supposed to start spinning with the water still in the tub? the direct drive washers have a neutral drain to pump out the water first and then switch over to spin. puts a lot less strain on the motor. just wondering if this model has one and it's not working right.
For model number MAVT236AWW
Hi Charles,
Thank you for your question. There is no neutral drain kit listed for your washer. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Stephanie
December 30, 2019
What size washer drum does this washer take
For model number MAVT236AWW
Hello Stephanie and thank you for writing.
For your convenience, we have attached the link to your manual with instructions. We hope this helps. https://partselectcom.azureedge.net/assets/manuals/7BFCD425FDFC46C34CDA8FAA23CABC849D03176F.pdf
Was this helpful?
Thank you for voting!
Steve
April 9, 2023
Can you buy just the pulley and belt for drive motor. And the beating for the water pump
For model number MAVT236AWW
Hi Steve, thank you for contacting us. The parts you are looking for are the drive belt, part number PS11738882, and the transmission pulley and bearing kit, part number PS2003651. The bearing for the water drain pump is included in this kit. If you require assistance to place an order, please contact customer service!
Clothes are still wet after the spin cycle. Is it normal that I can stop the spin drum by applying pressure to it while it is spinning in the spin cycle? I replaced the belt with a newer one, but it did not fix the issue. What could possibly be the issue? Thank you.
For model number MAVT236AWW
Hi Andy,
Thank you for your question. If your clothes are sill wet after the spin cycle, you may have a clogged drain pump or drain hose. Unplug the washer from the electrical outlet before removing and inspecting any part in your washer. If the drain pump and hose are clogged they will need to be cleaned. If they show signs of damage, you will need to replace them. If you have overloaded the washer and it becomes unbalanced, then the water will not spin out of the clothes and they will remain wet. Do not overload the washer and wash smaller loads. If you are pressing on the washer lid and the washer stops, the lid switch may be faulty. You will need to test it for continuity with a multimeter on the Rx1 setting to see if it is operating normally. First check to see if it is operating mechanically and that the levers and actuators are not sticking or damaged. If you are able to operate the lid switch mechanically, test it with the multimeter. Touch the probes to the terminals, then press and hold the switch button down. You should receive a reading of zero. If you do not receive this reading, you will need a replacement lid switch. We hope this helps!
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it.
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed. Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Maytag Washer")
