MAH5500AWQ Maytag Washer - Instructions

Followed the inclose instructions that came with the Motor and Control Board Conversion Kit very easy.

I looked at the exploded view that was posted on the website which was a big help. I took off the back and took off the control knob. I then unscrewed the timer from the console and it took a couple of minutes to realize that the timer moved to the left and had these lugs that anchored it to the console. The fact that there was only one screw should have been a give away. The hard part was disconnecting the wiring plug from the old timer.
The install was in reverse and easy.
The only problem is that while the washer no longer stops at every step of the cycle it still periodically stops at the 2nd and the 3rd rinse.
I don't know what that is, I suspect it is a relay but I am having trouble figuring out which relay it is.
Overall, it ws a piece of cake and the washer does run better.

Removed five screws from rear of control panel.
Removed two control board mounting screws.
Replaced control board.
Replaced all screws.
Washer worked except for temp control.
Opened front door and removed four screws.
Removed front panel.
Removed two lock tab screws and locking tabs.
Lifted up top of washer.
Unplugged cable from thermistor.
Closed washer top and reinstalled locks and front panel.
Temperature control switch now controls temperature without using the thermistor+.

removed 5 screws from back of control panel holding back panel cover. removed control knob from front of control panel. removed screw holding Timer. slid Timer module to right and pulled Timer out. disconnected plug from old module. plugged
new module in and reversed previous removal procedure. Unfortunately this did not correct the problem as machine still stops at rinse cycle and shuts down. misdiagnosis on my part. called repairman and he diagnosed a bad control board.
Cost is 3 times cost of Timer alone.

Removed the front panel and took out the old control board, which had a burnt spot on it. Removed back panel and took out the old motor. Put in the new motor and then the new control panel. Runs perfect.

first i follow the instruction come with parts in box...and replace easy this the best place to buy parts for all home appliance...thanks

followed the diagnostics instruction in the Maytag Owners booklet which pointed to the Motor Control Assembly.
PartSelect was a very good choice for securing the part.

Followed the troubleshooting procedure that came with the
washer.Found problem,(with a little help from my experience
in electronics). Order motor and control board kit.
Followed the easy instructions that came with parts and
had it working in no time!!!!
Good job PartSelect !!!!

Had to move all the concoctions my wife uses on my greasy work clothes [ purple power, dawn dishwash soap,lestoil, etc..] Removed front , removed back panel..Replaced board then motor..Replaced belt while I was in there.I had already changed out the tub bearing assembly earlier..Quite a complex machine when you get in that deep..Runs like new...

Removed old motor installed new motor.

1) Removed machine front by removing four (4) screws. 2) Removed rear access panel. 3) Replaced antiquated motor controller with upgade revision; basically unplug and plug 4) replaced motor and 5) closed up unit. Whole job took about an hour with half the time spent moving the unit to work oo.

I removed top control panel and then the old power cord that been damaged by a small fire and the just attached the new power cord and control panel. Unblievably simple and I saved myself a lot of money. Where I live in a NYC suburb this type of simple repair could easily cost $100.

Used the conversion kit to replace both parts.Note the supplied instructions say to test the install by running a spin cycle before you put the door and panels back on. However the unit will not initiate a spin cycle without the door lock engaged. Not just the light switch, the actual door lock mechanism. You have to reinstall the door, then test. This error in the instructions cost me about 30 minutes.

Ordered siphon cap according to FPS parts list. Wrong cap, but I don't care! Customer support was so helpful and willing to do everything to get me the correct cap, to include refunding my purchase price AND shipping before I even sent it back. They will be my first choice for parts in the future! My husband is a "fix it" guy, so I know that will mean a lot of purchases. I look forward to future business with this company!

Our rental house washer had the parts removed by the last tenant, just replaced them. Thanks!