LRE30453SB (FBKLLGA) LG Range - Overview
Sections of the LRE30453SB
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Temperature Sensor
PartSelect #: PS11732697
Manufacturer #: EBG61305805
This temperature sensor, also referred to as a thermistor, is a genuine replacement component compatible with various appliance models. It works in coordination with the control board to monitor inter...
$103.87
In Stock
WINDOW,GLASS
PartSelect #: PS16661222
Manufacturer #: 4890W1N009H
This clear inner glass lets you see inside your LG oven while keeping the heat in. If your oven glass is cracked or chipped, replacing it helps restore energy efficiency and safe cooking. It’s made to...
$150.30
In Stock
SHELF
PartSelect #: PS11775895
Manufacturer #: MHL39256107
Upgrade your oven with this durable gliding shelf rack, designed to provide a stable surface for baking, roasting, and broiling. Its smooth sliding design makes it easy to insert and remove dishes, of...
$118.81
In Stock
Questions And Answers for LRE30453SB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the LRE30453SB
[Viewing 8 of 8]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Door won’t open after self cleaning cycle
Fixed by
these parts
these parts
Show All
Won’t turn on
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven would initially start to heat up but would not hold its temp
I searched online and found someone that seemed to have the exact problem. That person had replaced the lower burner and the same PCB board I replaced. I was able to test the lower burner without removing it and it tested OK. The PCB board in the article I had checked was burned and obviously bad but mine was not. I took a chance and ordered just the PCB board. I replaced this board and the oven now works perfectly. I seems this board was not turning on the bottom burner but the system thought it was working fine.
Parts Used:
-
Leonard from Plano, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Glass heating element not working
Very easy.1: Shut power to stove.
2: Remove 3 hex screws from oven to range top at underside of top.
3: Raise to from front and disconnect multi- connector at right rear of top.
4: flip over top and demoed 4 screws on hold down strap at each side.
5: Remove element from under strap.
6: Disconnect element from wires./ remember where wires were connected. Connect multi connected from stove.
7: Replace strap and flip top, screw it back on, put power back on.
Only about 30 minutes even if you get a coffe break. Don’t even have to move stove.
2: Remove 3 hex screws from oven to range top at underside of top.
3: Raise to from front and disconnect multi- connector at right rear of top.
4: flip over top and demoed 4 screws on hold down strap at each side.
5: Remove element from under strap.
6: Disconnect element from wires./ remember where wires were connected. Connect multi connected from stove.
7: Replace strap and flip top, screw it back on, put power back on.
Only about 30 minutes even if you get a coffe break. Don’t even have to move stove.
Parts Used:
-
Paul from TRUMBULL, CT
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not reach set operating temperature
Removed the back of the Range. Removed one wire at a time from the old PCB and placed it in position on the New PCB. Then secured the New PCB in the holder.
Parts Used:
-
Charles from Camden, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!