This crisper cover front support is used to keep the crisper shelf in place and may need replacing if the door will not open or close. This white, OEM part measures roughly 1 inch in diameter and can ...
$15.17
In Stock
Order within the next 5 hrs and your part ships today!
This authentic rear crisper support is a white, plastic part which is rated as "easy" to install by our customers. This OEM part replaces the rear crisper cover support in your fridge and mounts to th...
$18.97
In Stock
Order within the next 5 hrs and your part ships today!
This part releases water from the supply line when it's activated. NOTE: This part may appear different than the original, but is an authorized manufacturer replacement.
$129.55
In Stock
Order within the next 5 hrs and your part ships today!
This cover holds up the top crisper drawer, and has drawer glides molded in it. This upper crisper drawer cover is a manufacturer-approved replacement part for your refrigerator. It has drawer glides ...
$89.48
In Stock
Order within the next 5 hrs and your part ships today!
This original equipment manufacturer Door Shelf is a white plastic part which holds items inside of your freezer or refrigerator door. It is roughly 10 inches long by 4 inches high by 5.5 inches wide....
$62.14
In Stock
Order within the next 5 hrs and your part ships today!
This bin can be moved according to space needed. It holds items on the door of your refrigerator.
NOTE: This bin is only available in clear plastic now.
$121.35
In Stock
Order within the next 5 hrs and your part ships today!
The run capacitor is attached to the compressor. This part is 120 volts and 15 mfd. The run capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things froze...
$48.68
In Stock
Order within the next 5 hrs and your part ships today!
This clear plastic crisper drawer is for side-by-side refrigerators. It is sold individually and sourced right from the original manufacturer. Please note that the new pan does not have the humidity c...
$121.66
In Stock
Order within the next 5 hrs and your part ships today!
Keep your produce fresh and your fridge organized with this crisper pan cover frame. It fits above the bottom drawer and helps control humidity levels for fruits and vegetables. The frame is sturdy an...
$105.75
In Stock
Order within the next 5 hrs and your part ships today!
This is the replacement water filter base for your refrigerator. It is approximately 3-1/2 inches by 3 inches. It is made of white plastic with two blue water filter receptacles. The water filter base...
This refrigerator crisper glass insert is a genuine OEM replacement designed to restore the functionality and organization of your appliance’s lower storage area. Measuring approximately 17.12 inches ...
$144.67
In Stock
Order within the next 5 hrs and your part ships today!
Questions And Answers for LFSS2612TP5
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lynn
September 20, 2021
I bought my refrigerator through lowes in january. This is the 2nd time ive had problems with the ice maker. My ice maker and water on the fridge isn't working. The water just drips if you try to get some out and the ice maker isn't making any ice.
For model number LFSS2612TP5
Hello Lynn, thank you for your question. Water may not be reaching the ice maker due to a frozen line, clogged filter, or a closed water inlet valve. First check the water lines to make sure they are not frozen. If they are frozen, you can defrost them with a hair dryer or by unplugging the refrigerator. Make sure that the filter is in place, and if it has not been changed recently, replace it with a new one. Part number PS3412266. If the filter is good and the lines are not frozen, you can test your water inlet valve with a multimeter. Disconnect the water supply line connected to the valve, and disconnect the wires from the terminals located on the solenoid coils. Set the multimeter to the lowest Ohms of resistance, and make sure the meter is calibrated properly. Place a probe on one of the terminals, and place the other probe on the other terminal. Do this for each solenoid coil. If the meter measures infinite Ohms of resistance– the display on a digital meter does not change much or the needle on an analog meter does not move– the valve has no continuity and needs to be replaced. Part number PS7784018. We hope this helps.
Flashing H1 need sensors for both freezer and refrigerator
For model number LFSS2612TP5
Hi Polly, thank you for reaching out. The part you are looking for is a thermistor assembly, part number PS8760187. It is for both the fridge and freezer. We hope this information helps!
I need to replace one broken wire shelf in freezer . Requesting to order please.
For model number LFSS2612TP5
Hi Amalia, thank you for getting in touch. The compatible wire shelf that goes over the freezer basket is part number PS1148755. The upper wire shelf is part number PS1148757, and the middle wire shelf is part number PS1148756. You may need to replace the broken one to fix the issue. If you need help placing an order, customer service is open 7 days a week!
Sitting in the living room and noticed that there were flames coming from underneath my refrigerator a little black box that was connected to the power cord, could this be the Run capacitor, if so why?
For model number LFSS2612TP5
Hi Timothy,
Thank you for your question. The run capacitor would be plugged into the compressor. Are you referring to the compressor? If you could resubmit your question with this information, we would be happy to help you. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.
Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle. A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if the maker dumped the ice into the bin.
