This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
Sold individually. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward.
The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. At around 3 inches in length, the clip is used to keep the tine row in place in the ...
This manufacturer-approved Rack Stop Clip is a gray plastic part which can be installed with a screwdriver. Measuring slightly over an inch in length, it prevents the rack from sliding too far and fal...
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the bo...
Prevent leaks and maintain optimal cleaning performance with this durable dishwasher door seal. It creates a secure barrier to keep water contained during wash cycles, ensuring reliable operation. Rep...
This part is the replacement door seal for your dishwasher. It is approximately 22 inches long and 2 inches wide. This door seal is made of gray plastic and is found at the bottom the dishwasher. The ...
Also known as rack adjuster. Sold individually.
This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip...
This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.
$37.43
In Stock
Questions And Answers for KUDS30IXWH1
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Joseph
June 14, 2023
I replaced panel, door latch, and board, still have to turn off breaker to get it to work right.
For model number KUDS30IXWH1
Hello Joseph, thank you for the query. Since you have replaced the most common parts that can cause this issue. We would recommend checking the high-limit thermostat, part number PS11750035. If the thermostat is malfunctioning, it will cause this issue and the dishwasher will not complete its whole cycle. We hope this helps!
I have replaced
control panel
door latch
control board
and both fuses
I still have to turn off breaker to run a cycle
and it will run a complete cycle with no issues
thank you for your time
For model number KUDS30IXWH1
Hello Joseph, thank you for the question. According to our research, if resetting the circuit breaker is correcting the problem, that means your control board inside the door of your dishwasher is starting to fail. Just like a computer, restarting or rebooting the board will sometimes get the unit to work again. We would recommend you to check that you have replaced the board with the compatible control board, part number PS11753985, and also check that the control board is installed correctly. We hope this helps!
Replacement was pretty easy after figuring out how to unsnap/unlock the old pieces. Tools only used to do a little prying and poking, but really aren't needed. Everything either snaps or slides together. Piece of cake
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
I took the broken basket adjuster off and then attached the new one. It wasn't too difficult, however some removal instructions and re-install instructions( or just a picture supplied) would have been helpful. This isn't an issue for a mechanically inclined person, but would be a challenge for someone that isn't. Thanks.
