This part chops up/mince the food particles to prevent from clogging the dishwasher pump. This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up...
Sold individually. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward.
This is a door seal, but you may also know it as a door gasket and it is a part for your dishwasher. It provides a leak proof seal between the tub and the door of your appliance. You will need to repl...
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve will open and close according to the desired amount of water needed.
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This part contains the mounting clips and helps distribute water from the top of the dishwasher tub.
$57.00
In Stock
Questions And Answers for KUDP01DLBL1
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Joyce
February 27, 2020
Does this model have a filter that needs to be cleaned?
For model number KUDP01DLBL1
Hi Joyce, thank you for your question. Yes, it does have a filter that you could gently clean out with hot soapy water if it gets clogged up. This is the part: PS897295. We have an installation video for it here: https://youtu.be/DCL17ts6RDU. That should help you with how to properly remove it. We hope that helps. Good luck with your repair.
"normal" and sensor is blinking. Dishwasher will not start. How do i reset?
For model number KUDP01DLBL1
Hello Debra, Thank you for your inquiry. To reset the dishwasher control panel, it needs to be disconnected from the power source for one minute. If your dishwasher is plugged into an outlet, simply unplug the unit for one minute and then plug the unit back in. If the dishwasher is hard wired to the power supply, turn the breaker off at the home electrical panel that powers the dishwasher for one minute and then turn the breaker back on. Hope this helps.
Was this helpful?
Thank you for voting!
Jane
March 23, 2023
Dishwasher does not drain. Ive cleaned all parts.
For model number KUDP01DLBL1
Hello Jane, thank you for getting in touch. According to our findings, you should inspect the sump filter. If it is clogged, you will have low water flow and poor washability. To clean the filter, remove it and wash it with soap, warm water, and a brush. If the filter cannot be cleaned effectively or if it is damaged, replace it with part number PS392942. The next thing to check is the drain pump. The drain pump uses an impeller to force water through the drain hose. If the drain pump motor is not working, the dishwasher will not drain. To determine if the drain pump is defective, check the pump motor for continuity using a multimeter. If the motor does not have continuity, or if it is getting power but will not run, replace the drain pump, part number PS11743433. Inspect the drain hose, part number PS2358130, to fix the issue. We hope this helps, good luck with this repair!
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails. 2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight. 3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn. 4) Remove the strainer cover by unscrewing the 4 Torqs screws. 5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover. 6) Pull out the broken Chopper Assembly, make sure you get all the pieces! 7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly. 8) Put everything back together and make sure it works!
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.