This twenty-five watt microwave light bulb is two and a half inches long. It has a small, screw-in base and it carries 120V. This item sells in a quantity of one, though many microwaves require two.
This set of two electronic control boards contains both the emitter and the receiver. These boards tells the icemaker when it's full and that it has to dump the ice, and it also tells the icemaker whe...
If your refrigerator or freezer is too warm, or making noises, you may need to replace the fan blade. The fan blade attaches to the evaporator motor, which is in the freezer section, to help circulate...
Metallic screw that is less than an inch long. Does not include the plastic washer.
$10.09
In Stock
Questions And Answers for KSSC42QTS00
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gity
December 12, 2019
My ice maker is working but the plastic part that does not let the air go to the part ice lose and there for ithink this part call like shoe tung will you please help me to find that part
For model number KSSC42QTS00
Hello Gity, thank you for your question. I think you're talking about the arms that push the ice into the bucket. Those are parts Part #: PS11743312 and Part #: PS2378115. Please enter the part number into the site for current price and availability. Good luck with your repair!
Was this helpful?
Thank you for voting!
Ziad
July 25, 2021
How to put back the ice bin together. Where does the spring go?
For model number KSSC42QTS00
Hello Ziad, Thank you for the question. The Spring is located on the Latch. Here is a repair story from another customer on replacing this part that may help. Good luck with the repair ! It's best to remove the shelf barrier under the ice dispenser assembly (pops off) for ease of access - the motor hatch is a bit awkwardly placed. Removing 2 x 1/4" screw nuts pops off the lower hatch on the underside of the ice dispenser assembly. Inside, remove the wire connector + 4 x 1/4 nut driver screws and the whole motor is released, while the hex drive shaft remains attached to the dispenser assembly. No sweat so far. The new motor pops in the same way the old one came out - you might need to give the top of the hex drive shaft a twist to align. A powered nut-driver is recommended to do all of this yoga 2 feet off the floor with only 2 hands. Secure the 4 nut screws and reconnect the wire connector and you're almost done. But wait - read the directions and you notice that there's a rubber washer that has been introduced to prevent water leeching into the motor. didn't see that little thing in the shipping box - ok so I get to do this twice... don't make the same mistake. Attach that rubber washer to the hex shaft. Then, reattach the panel with 2 more nut screws and you really are done. We hope this helps!
Hello Marcia, thank you for your question. If you need an assembled ice maker then part number PS11751735 is compatible with your model. It contains the complete ice maker parts and housing. If you are looking for an ice container, part number PS11739788 will fit your model. It stores ice in the freezer compartment for dispensing. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
Left fridge on wheels without lowering legs and are now out of round (flat).
Very dumb, Had kitchen floors refinished and guys forgot to lower legs 6 years ago.
Can these be replaced? Part numbers?
For model number KSSC42QTS00
Hello William, thank you for reaching out. According to our understanding, you may need to replace the roller wheels. The front and rear rollers for your model have part number PS11748930. They are sold individually. If you need help placing an order, customer service is open 7 days a week!
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours.
First I shut the water off to the refrigerator.then i pushed the big button in the middle of the grille below the refrigerator door. pulled out the old filter, took the front cap off the old filter put it on the new filter. took the two red caps off the new filter. pushed the filter in till it locked in place. all done! Turned the back on.