KSM55 Mixer - Overview
Models starting with KSM55
Click on the best match to narrow your results.
- KSM55SJSXBM0 KitchenAid Mixer (Model # Ksm55sjsxbm0 Official Kitchenaid Stand Mixer)
- KSM55SJSXCU0 KitchenAid Mixer (Model # Ksm55sjsxcu0 Official Kitchenaid Stand Mixer)
- KSM55SJSXER0 KitchenAid Mixer (Model # Ksm55sjsxer0 Official Kitchenaid Stand Mixer)
- KSM55SJSXMI0 KitchenAid Mixer (Model # Ksm55sjsxmi0 Official Kitchenaid Stand Mixer)
- KSM55SJSXVB0 KitchenAid Mixer (Model # Ksm55sjsxvb0 Official Kitchenaid Stand Mixer)
- KSM55SXBXIB0 KitchenAid Mixer (Kitchenaid Stand Mixer)
- KSM55SXTXIC0 KitchenAid Mixer (Kitchenaid Stand Mixer)
- KSM55SXXXAG0 Whirlpool Mixer (Mixer)
- KSM55SXXXBM0 KitchenAid Mixer (Kitchenaid Stand Mixer)
- KSM55SXXXCU0 KitchenAid Mixer (Model # Ksm55sxxxcu0 Official Kitchenaid Stand Mixer)
- KSM55SXXXER0 KitchenAid Mixer (Kitchenaid Stand Mixer)
- KSM55SXXXOB0 KitchenAid Mixer (Model # Ksm55sxxxob0 Official Kitchenaid Stand Mixer)
- KSM55SXXXPL0 Whirlpool Mixer (Mixer)
- KSM55SXXXWH0 KitchenAid Mixer (Model # Ksm55sxxxwh0 Official Kitchenaid Stand Mixer)
Keep searches simple, eg. "belt" or "pump".
Mixer Retaining Ring
PartSelect #: PS11746917
Manufacturer #: WP9703680
Used on Stand Mixers.
$11.99
In Stock
Wire Whip
PartSelect #: PS11746914
Manufacturer #: WP9703491
This part is the replacement wire whip for your stand mixer. It is made of metal and is approximately 7 inches from top to bottom, and 5 inches from side to side. The wire whip is an attachment which ...
$43.53
In Stock
Bowl Arm Lift
PartSelect #: PS11746961
Manufacturer #: WP9706885
This is a replacement bowl arm lift for your stand mixer. It raises and lowers the mixing arm in the bowl. It is made of white plastic and is sold individually. This part can also be known as the bowl...
$12.77
In Stock
Coated Flat Beater
PartSelect #: PS11757062
Manufacturer #: WPW10672616
The Coated Flat Beater is an OEM accessory specifically designed for 5 and 6 Quart KitchenAid stand mixers. This flat beater is responsible for thoroughly incorporating ingredients when mixing or blending recipes.
$35.42
In Stock
Range Torx Screw
PartSelect #: PS11741257
Manufacturer #: WP3368921
7-18 x 3/4-Inch - sold individually.
$8.82
In Stock
Flat Metal Beater
PartSelect #: PS16875729
Manufacturer #: W11646967
This Flat Beater is used as a mixing attachment for all six quart mixers and some five quart mixers. The Flat Beater is made from metal and has a burnished finish. This part attaches to the mixer on t...
$59.54
In Stock
Mixer Pingroove
PartSelect #: PS11750745
Manufacturer #: WPW10234531
This groove pin is a small but essential metal piece used in stand mixers to secure the internal gears and keep the planetary assembly firmly attached to the drive shaft. When this pin wears out or br...
$11.93
In Stock
Common Symptoms of models starting with KSM55
[Viewing 2 of 2]Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The mixer would not raise the bowl
I removed the motor assembly from the mixer. This left the stand assembly. The raising lift arm had to be removed by unscrewing the set screw, and then the lift arm was removed. I replaced the plastic arm bowl lift by sliding it over the lift arm, and then I had to remove the spring with a clip washer with the pliers, and replaced the spring back on to the new part. Total time about ten minutes for the actual fix, and about 45 minutes remove and reinstall the 12 screws that held the motor in place. It was well worth my efforts. The mixer arm works perfectly now.
Parts Used:
-
Stephen from Charlotte, NC
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
12 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
all four feet on mixer damaged
I first ahd to remove the original feet by removing screws that held them in place. The new feet that I purchased were different then the original. They were a push in type and not held in by screws. I had to modify the base by drilling the foot holder to accept the new style feet. Once this was done, the feet were installed and looked good.
Parts Used:
-
ROBERT from ENDWELL, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dough mixer paddle not turning.
-
Iftikhar from PACIFICA, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!