This Refrigerator Air Filter is a white 1.8x3.2" plastic filter which neutralizes odor and bacteria in the air. It should be replaced every six months at a minimum. Refer to your user manual and model...
This compressor start relay is for refrigerators. The compressor start relay attaches to the compressor and helps start the compressor motor. Safely store any food that could deteriorate while the pow...
Experience the simple solution to a wobbly refrigerator with the Whirlpool Refrigerator Leveling Leg. This authentic, factory-made part is designed to keep your refrigerator stable and even, saving yo...
This auger motor is for refrigerators.
Auger motor turns the auger that pushes the ice cubes through the dispenser chute.
Safely store any food that could deteriorate while the power is off. Unp...
The ice maker includes the ice mold and the control device. The ice maker receives water from the water inlet valve and then holds the water in the ice mold until the water freezes solid.
The compressor run capacitor keeps the refrigerator motor running smoothly. Be sure to unplug the appliance before installation and verify the part number for compatibility.
This water filter is a genuine replacement for bottom-freezer refrigerators that accept a Filter 2. it is certified to remove up to 24 different contaminants which include pharmaceuticals, waterborne ...
This door gasket is used to make an air-tight seal for the cabinet when the door is closed.
$264.54
In Stock
Questions And Answers for KRFF577KBS02
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
JOE
July 5, 2025
THE FRIDGE IS TOO WARM AND WON'T COOL. ALL FOOD WENT BAD. BROUGHT THE FRIDGE ONLINE AT KITCHEN ON AUGUST 23, 2023
O RAN ALL PANEL TESTS. RAN TEST 4 FOR THE COMPRESSOR IT BUZZED IN THE FIRST TEST TRYING TO START UP.
COMPRESSOR KICKS ON FOR 5 TO 7 SECONDS AND THEN STOPS IN TEST 4 AND WHEN I TAKE IT OUT OF TEST MODE..
O CHANGED THE CONTROL BOARD, THE START RELAY AND CAPACITOR AND THE FILTER.
QUES 1: DOES THE FRIDGE HAVE AN INVERTER OR A DEFROST TIMER? (DIDN'T FIND THEM IN YOUR ONLINE PRINTS.
QUES 2: ANYTHING ELSE I CAN DO?
For model number KRFF577KBS02
Hi Joe, thank you for the question. There is no inverter or defrost timer listed in your model. As you have already replaced all the necessary parts, the compressor not staying on suggests a potential issue with the compressor itself. Its part number is PS17916888. We hope this solves your problem!
Purchased new motor from Partselect.com. When it arrived it came with a new rubber washer that fitted on top of new motor that was not on old motor, that how water got into old motor. However, the instruction sheet did not give info on how to access the proper way to the motor that is the door. Not wanting to damage the freezer door assy. called in a tech who made it look easy, but even he had a little problem locating access panel that was directly under the motor in the freezer side of the door. After that it was a piece of cake.
The repair seemed simple, I just needed to remove the old bracket -- 4 screws -- and slip the new one on.
The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, I needed to shim up the side of the fridge that I was working on.
To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.
