Includes both the attachment and beveled gear. This worm follower gear is for stand mixers.
Worm follower gear meshes with the worm gear, causing the rotation of the planetary assembly where the ac...
$35.88
In Stock
Order within the next 8 hrs and your part ships today!
Keep your stand mixer running smoothly with this replacement worm gear, which powers the planetary assembly where beaters and other attachments connect. Made from high-quality metal, it’s built to wit...
$66.36
In Stock
Order within the next 8 hrs and your part ships today!
If your stand mixer isn’t adjusting speeds like it used to, this speed control switch might be the fix. It comes with the black knob and lets you fine-tune how fast your mixer runs—perfect for everyth...
$125.33
In Stock
Order within the next 8 hrs and your part ships today!
This part is the replacement wire whip for your stand mixer. It is made of metal and is approximately 7 inches from top to bottom, and 5 inches from side to side. The wire whip is an attachment which ...
$43.53
In Stock
Order within the next 8 hrs and your part ships today!
This is a replacement bowl arm lift for your stand mixer. It raises and lowers the mixing arm in the bowl. It is made of white plastic and is sold individually. This part can also be known as the bowl...
$12.77
In Stock
Order within the next 8 hrs and your part ships today!
Questions And Answers for KP2671
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ralph
October 23, 2024
Is speed control avalable for KP2671XGR mixer
For model number KP2671
Hello Ralph, Thank you for contacting us. Researching your model, we show the compatible speed control assembly as part# PS11746947. We hope this helps you.
This is not my full model # it’s kp2671xgr. I re-looked at the tag with the serial\model #’s and there isn’t any numbers others than those 2. It’s a Professional 6 with the raising and lowering bowl lever. I was using the mixer while running it shut off and I tried (user error) to move the power switch to off and it was stuck, unfortunately I broke the actual power knob off in the process. So I’m pretty sure it’s more than one issue but if you could help me figure out what I need to fix parts wise would be great.
For model number KP2671
Hi Margaret,
Thank you for your question. If the attachment you were using was loose, the mixer may have stopped. If that is not the issue, it may have stopped due to a malfunctioning motor, control board, or a power issue. Based on what you described, the issue may be with the stand mixer speed control board, part number PS11746947. It includes the knob and controls the speed of the mixer. We hope this helps!
Removed four screws to remove main cover. Removed four more screws to remove fractured plastic gear housing cover. Removed retainer ring and slid two gears and dowel off main shaft. Lifted out remaining gear train and bearings, Removed all grease and metal chips from all components. Greased new gears and reassembled. Replaced plastic gear housing cover with oreviously purchased die cast replacement part. Assembled main cover.
removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease ( do this to get all the metal shavings out from the failed gear) repace the grease in the gear housing and reassemble in reverse order
Removed screw from back of mixer cover band and then removed the 4 side screws, lifted top off of mixer and removed screws from circuit board control switch, removing wires one at a time so as to install correctly. replaced screws in circuit board/control. Restored top of mixer replaced screws and the put cover band back on mixer.walla done
