This OEM Dishwasher Upper Rack Adjuster is a grayish-black, plastic part which will require a screwdriver to install. It fits onto the dishwasher rack and connects it to the track allowing it to slid...
This gray plastic lower dishrack roller is a part for your dishwasher. It attaches to the bottom of the lower dishrack, allowing it to move in and out smoothly. If the lower dishrack stops moving in a...
Sold individually. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward.
Also known as rack adjuster. Sold individually.
This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip...
This part is the replacement door seal for your dishwasher. It is approximately 22 inches long and 2 inches wide. This door seal is made of gray plastic and is found at the bottom the dishwasher. The ...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
Sold individually.
This dishrack adjuster is for dishwashers.
Dishrack adjuster lets you change the height of the dishwasher's upper rack.
Wear work gloves to protect your hands when installing this part.
$58.76
In Stock
Questions And Answers for KDFE104DWH0
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rosemary
February 24, 2022
Only control lock light works on the control panel
For model number KDFE104DWH0
Hi Rosemary,
Thank you for your question. If your dishwasher is stuck on control lock, press and hold control lock for 3 seconds and the light should go out. To reset the control lock and press and hold it again for 3 seconds. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Angeline
June 15, 2021
How to remove the upper rack. The upper rack track is broken.
For model number KDFE104DWH0
Hello Angeline, Thank you for the question. To remove the Upper Rack you will need to release the Stops at the end of the rails and pull the rack all the way out from the rails. We hope this helps!
Was this helpful?
Thank you for voting!
Byron
January 18, 2023
Our water is not heating in this dishwasher. What troubleshooting steps should one take to prove that this is either the heating element or if this is a problem with the heating element got getting voltage?
For model number KDFE104DWH0
Hi Byron, thank you for reaching out. We would recommend testing the Heating Element for continuity with a multimeter. If there is no continuity, replace it with part number PS9494999. If that does not take care of the issue, we would recommend replacing the Thermostat, part number PS11750035. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.
Thought Dishes were washing, but when opened door to remove dishes
I found the soap cube was laying in the bottom of dishwasher. Dishes had not washed.
For model number KDFE104DWH0
Hi Sara, thank you for asking. It sounds like there may have been an issue with the dishwasher detergent not properly dissolving or dispensing during the wash cycle. It can happen due to the following reasons: Dishwashers require hot water to dissolve the detergent effectively. If the water temperature was too low, the detergent cube may not have dissolved completely. Check your water heater settings to ensure that it is providing hot water at the recommended temperature for dishwashing. Sometimes, the detergent dispenser compartment can get blocked or obstructed, preventing the detergent cube from being released. If this does not help, you may need to check the detergent dispenser, part number PS11773088, to fix the issue. It holds the dishwasher detergent and the rinse agent in covered compartments. If the dishwasher does not get detergent, the dishes will not be clean. We hope this sorts out your problem!
Replaced dishwasher control board, now have error code 6-6. Any suggestions? Water is hot enough.
For model number KDFE104DWH0
Hello Jerry, thank you for your inquiry. This error code indicates that the water in the dishwasher is not heating to the required temperature. To remove the error code, check that the water is hot by turning the dishwasher on and pausing it once the wash cycle starts. At that time, check if the water is hot. If not, replace the thermostat, part number PS11750035, to fix the issue. We hope this information helps!
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water input line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
