JVM3160DF3CC General Electric Microwave - Overview
Sections of the JVM3160DF3CC
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Charcoal Filter
PartSelect #: PS8746150
Manufacturer #: WB02X11550
This is the replacement charcoal filter for your microwave. It is silver and black in color and measures approximately 10 inches by 2 ½ inches. The charcoal filter removes cooking odors from the air ...
$70.19
Special Order
Light Bulb - 40W
PartSelect #: PS8767095
Manufacturer #: WB25X10030
This is a genuine replacement 40 watt bulb for a microwave. The bulb is meant to light up the underside of the microwave or inside of your microwave when the door is open or during use. If your bulb i...
$48.14
Special Order
Grease Filter
PartSelect #: PS1022452
Manufacturer #: WB06X10608
Sold individually. Most appliances require 2.
$86.97
Special Order
ROTATING RING Assembly
PartSelect #: PS1016203
Manufacturer #: WB06X10625
When your microwave isn't heating your food evenly, the problem could lie with the rotating ring assembly - a crucial piece in ensuring proper function. Our GE Rotating Ring Assembly might just be the...
$46.54
Special Order
Microwave Door Latch Housing
PartSelect #: PS1019899
Manufacturer #: WB06X10610
The door latch housing encloses the door switches and door latch.
$76.27
Special Order
DAMPER BRACKET
PartSelect #: PS8753754
Manufacturer #: WB06X10938
Do you have a microwave that's not performing to the best of its ability? It might be time to consider GE's Damper Bracket. Designed particularly for microwave appliances, this high-quality component ...
$107.62
Special Order
Microwave Turntable Motor
PartSelect #: PS12722592
Manufacturer #: WB26X32190
This turntable motor is for microwaves.
The turntable motor rotates the glass tray inside the microwave oven.
Because high-voltage capacitors in a microwave can retain a lethal electrical charge...
No Longer Available
Microwave Installation Hardware Kit
PartSelect #: PS1021433
Manufacturer #: WB01X10298
$122.72
Special Order
Microwave Door Interlock Switch Lever
PartSelect #: PS8753607
Manufacturer #: WB03X10348
The door interlock switch lever activates the interlock switch when the door is closed.
No Longer Available
Microwave Turntable Motor Coupler
PartSelect #: PS8753744
Manufacturer #: WB06X10925
The turntable motor coupler connects the turntable motor to the turntable tray to rotate the tray.
No Longer Available
Questions And Answers for JVM3160DF3CC
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Marcelo
July 5, 2021
Fuse in the fuse box pops .As soon as the microwave starts
For model number JVM3160DF3CC
Hello Marcelo, Thank you for the question. We suggest testing or replacing the Door Switches. If the switch is defective it will send a surge and trip the breaker or blow the fuse. We hope this helps!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the JVM3160DF3CC
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bulb burned out under the microwave that lights the cooktop underneath
got a screwdriver and opened the glass door over the light bulb - changed the bulb and put the glass door back with the screwdriver.
Parts Used:
-
Margaret from TOANO, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
32 of 61 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tripping circuit breaker, broken micro switch locking pin
1. Unplug unit
2. Open door, remove two screws above the top trim piece, slide and remove trim.
3. Remove screw behind control board and top left corner, then release from position.
3b. Unplug all wire terminations and set control panel aside.
4. Remove two screws securing latch board, lift and rotate board out of position, remove three micro switches, xfer monitor switch actuator from lower pin in old board and insert in new. Install new door switches and reverse procedure to complete repair.
Note 1. Take care to located new latch board so holding tabs line up, pass through frame, and openings for door tangs line up with openings in frame before securing with screws.
Note 2. A long magnetic screwdriver is helpful.
2. Open door, remove two screws above the top trim piece, slide and remove trim.
3. Remove screw behind control board and top left corner, then release from position.
3b. Unplug all wire terminations and set control panel aside.
4. Remove two screws securing latch board, lift and rotate board out of position, remove three micro switches, xfer monitor switch actuator from lower pin in old board and insert in new. Install new door switches and reverse procedure to complete repair.
Note 1. Take care to located new latch board so holding tabs line up, pass through frame, and openings for door tangs line up with openings in frame before securing with screws.
Note 2. A long magnetic screwdriver is helpful.
Parts Used:
-
Charles from CLAYTON, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
16 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Had to replace charcoal filter
Open the front cover by pushing it at the top (where it says “Push”), lifting up and pushing back on top edge of the old filter. Pull it out. Installing the new one is basically just the reverse of those steps! That simple.
Old filter did seem to be a little thicker (filter material), but the new one was the exact same dimensions, so it went in properly. Wish the filter material was white, so you knew just how dirty it was actually getting. But... :-D
Old filter did seem to be a little thicker (filter material), but the new one was the exact same dimensions, so it went in properly. Wish the filter material was white, so you knew just how dirty it was actually getting. But... :-D
Parts Used:
-
Jared from SIERRA VISTA, AZ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
15 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!