This is the replacement charcoal filter for your microwave. It is silver and black in color and measures approximately 10 inches by 2 ½ inches. The charcoal filter removes cooking odors from the air ...
This is a genuine replacement 40 watt bulb for a microwave. The bulb is meant to light up the underside of the microwave or inside of your microwave when the door is open or during use. If your bulb i...
When your microwave isn't heating your food evenly, the problem could lie with the rotating ring assembly - a crucial piece in ensuring proper function. Our GE Rotating Ring Assembly might just be the...
Do you have a microwave that's not performing to the best of its ability? It might be time to consider GE's Damper Bracket. Designed particularly for microwave appliances, this high-quality component ...
This turntable motor is for microwaves.
The turntable motor rotates the glass tray inside the microwave oven.
Because high-voltage capacitors in a microwave can retain a lethal electrical charge...
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michelle
February 27, 2020
The microwave stopped working with no power at all. What can it be?
For model number JVM3160DF3BB
Hello Michelle, Thank you for the question. In most cases it is caused by a blown Fuse, PartSelect Number PS3486694. To get to the fuse, remove the outer cabinet of the unit, which is usually held in place with a few screws. Once the outer cabinet is removed, follow the power cord into the unit. It will take you to the fuse holder, where the fuse sits. The fuse holder is located two or three inches into the unit, and may be attached to a power board. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Robert
November 29, 2019
I have a model jvm3160df3bb microwave. Fan and light all work, as does clock and time. But when we place an item inside and enter any time and press start it trips the breaker feeding the the microwave circuit. There is nothing else on the circuit. It is a 20 amp breaker designated circuit. Any clue what to check first?? I have tried plugging it into a different circuit. lowering the power level etc. is it a door switch or something on the main board?
For model number JVM3160DF3BB
Hi Robert, if you are certain it is not an overloaded circuit then a part on the microwave is drawing more power than needed. Basically parts that could be drawing power could cause this, the motor, thermostat ect; Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
1. Unplug unit 2. Open door, remove two screws above the top trim piece, slide and remove trim. 3. Remove screw behind control board and top left corner, then release from position. 3b. Unplug all wire terminations and set control panel aside. 4. Remove two screws securing latch board, lift and rotate board out of position, remove three micro switches, xfer monitor switch actuator from lower pin in old board and insert in new. Install new door switches and reverse procedure to complete repair.
Note 1. Take care to located new latch board so holding tabs line up, pass through frame, and openings for door tangs line up with openings in frame before securing with screws.
Open the front cover by pushing it at the top (where it says “Push”), lifting up and pushing back on top edge of the old filter. Pull it out. Installing the new one is basically just the reverse of those steps! That simple.
Old filter did seem to be a little thicker (filter material), but the new one was the exact same dimensions, so it went in properly. Wish the filter material was white, so you knew just how dirty it was actually getting. But... :-D
