JVM1640BBC05 General Electric Microwave - Instructions

Above the stove mounted microwave. I dropped the lens cover from under the bulb and tried to remove the bulb. The bulb separated from the base. I tried to remove the base with a pliers and the lamp socket broke. I ordered the parts and dropped the bottom cover of the unit down (5 screws). Removed 1 screww from the lamp socket, unplugged the wires and took it out. Simply replaced socket, fastened bottom cover of microwave, installed new bulb and closed lens cover.

First I unplugged the microwave. :) Then, I removed the 6 screws found underneath the microwave, which allowed the bottom piece to hang down so I could see the turntable motor. I took the two screws out holding the motor in place and pulled the electric connectors off the motor terminals. Then I got the new part from PartSelect.com, replaced the electrical commectors, fit the motor back into the slot it came from (cause the pin has to be seated up in the hole) and replaced the 2 screws holding in the motor. Then I put the bottom metal piece back up and put the 6 screws back in. It was really easy - and I'm a chick! ;)

At first I tried to use pliers to unscrew the base,very uncomfortable working position,upside down and backwards(the microwave is installed over the range top)very limited space for your body and arms to manuver and you really cant see the base,all of this took place after the breaker was turned off ofcourse,finally figured out that you can drop the entire bottom housing of the microwave by unscrewing 6 screws and the light sockets are easily accessable once you lower it,take out 1 retaining screw ,remove the entire socket and unscrewed the broken base and replaced the bulbs,I said bulbs,there is no sense in having to replace another bulb in who knows how long since only one had burned out but they were both the same age

Had to take unit off wall and disassemble the main casing.then disconnected the wires from the magnetron.took the mounting nuts off but wasn't able to remove the magnetron until I loosened the transformer out of the way .Then it came out easy.Installed the magnetron ,tightened the nuts,installed the transformer back in, connected the the wires back on and installed the casing on ,screwed the screws and got help to install the unit to the wall again.....Tested the unit before putting back on the wall to make sure it heated....The parts were exac same type and wasn't too hard to do...

Unscrewed bottom plate of microwave and two screws that secured motor. Disconnect wires. Reversed process when installing new motor. Couldn't have been easier.

The tray drive motor arrived quickly. I opened the package and made sure the correct motor arrived. I shut off the power to the microwave/exhaust hood. Then I grabbed a screwdriver and dropped 5 screws from the bottom of the microwave. I then removed 2 more screws that hold the motor in place. Unplugged the 21 volt power clips. Placed the new motor in position and replaced the screws and attatched the power clips. I then placed the bottom pan in position and replaced the 5 screws that hold it to the bottom of the microwave. Turned the microwave on and it worked properly! The total cost was $40 and I probably saved more than a hundred dollars on a service call. What a happy ending and it took about 5 minutes to perform the repair! Thanks PartSelect. You are the best!

Unplugged the microwave first, then removed the screws that hold the cover in place. This gives easy access to the socket. Remove the screws that hold the socket in, unplug old socket, replace with new one and you are back in the light again.

Over the range microwave. Replaced magnetron. Completely disassemble the case top and bottom.
Remove screws from bottom of HV transformer. Magnetron will not clear without this removal.

Remove nuts with socket from top of Magnetron. Remove thermo unit from old magnetron and attach it to new. Replace and bolt down Mag. Replace and screw in HV transformer. Make sure all wires are reconnected.

Put it back up on the wall. Took about three hours from taking it down from wall and putting it back up.

1. remove microwave from wall
2. remove cover (many screws)
3. remove nuts holding magnetron in place (4)
4. remove magnetron (this is a pain due to the plastic molding used to direct cooling air through the magnetron
5. get new magnetron in place (this was even more fun to find the right angles to tilt to get the magnetron to fit
6. re-tighten the 4 nuts on the magentron
7. put the cover back on
8. put the unit back on the wall.

bonus repair: the display flickered while the magnetron was on (cooking ) prior to the magnetron dying. found a ribbon cable on the control board to the display with an aluminum foil shield that had peeled off (adhesive failure). re-installing the aluminum shield with packaging tape, and the display no longer flickers

After reading some of the comments that others wrote, I decided to order the light sockets along with the replacement bulbs. As predicted, the old light bulbs broke when I tried to remove them - the bulb separated from the base which was still screwed in the socket. After removing the screws that held the bottom panel, I was able to remove the socket assemblies with ease. After inspection of the old sockets, I was glad I ordered new sockets - the old sockets were burned in some spots and very brittle. The parts arrived within a day and a half after I ordered them, but when the parts arrived, one of the bulbs was broken (happened during shipping). I called the office phone number and talked to a really pleasant technician who refunded me the price of the broken bulb and placed an order for a replacement. That was the Wednesday evening before Thanksgiving Day. I got the replacement bulb yesterday (Tuesday) morning - still really quick considering the Thanksgiving holiday. All of the parts are installed and are working excellent. I am definately going to keep their WEBsite for future use, and I'll be letting my friends know about them. Thanks PartSelect, you've earned my business.

I broke the tray glass in the microwave cleaning it so this was a no brainer. The best part of this was the PartSelect experience. I ordered the part on the 30th of December and received it on 3 Jan!!! I have used PartSelect before for fridge repair and had the same experience.

No actual repair was necessary. However I do want to thank PartSelect for sending a replacement so quickly.

I ended up breaking one bulb trying to remove a burnt bulb for replacement. We then tried removing the other bulb and it wouldn't come out either. I googled the problem and found PartSelect and an explaination of the problem. Heat from either the stove or the bulbs had fused the bulbs into the sockets. Comments on the problem explained that you just remove the bottome pannel (we had seven screws), unplug the old sockets, insert the new and new bulbs and reattach the panel. It was quick and no problems to correct. We did discover the microwave was on its own breaker, make sure to disconnect or cutoff power to the microwave before you start.

This repair could not have been easier! The website was great at helping to identify the problem and the part needed. Users discribing how they did the repair gave me the confidence to do it myself. I got the part the day after I ordered it, installed it and my microwave was a good as new! It was as simple as unscrewing seven screws to remove the bottom of the microwave. Then two more screws to remove the part. Unplug the broken drive, plug in the new one and screw everything back together! Don't forget to unplug your microwave before you begin.

Great website!

Loosen screw holding glass cover plate in place over bulb. Glass cover plate will swing down. Unscrew bad bulb, replace with good bulb, reset glass cover and tighten screw.