JJW9630DDS32 Jenn-Air Wall Oven - Instructions

This is fairly easy for anyone to do. First I opened up the front (silver part) of the oven door by removing the screws at the top and the bottom. Then I kept on removing the various layers of glass... the 2 outside ones are removed by removing their respective screws and then you get to the inner-most. These 2 inner ones are in a frame that holds them together. I removed the large silver frame that holds the insulation and the 2-glass-frame in it. Just remove the screws and then tilt the insulation frame out a bit to remove the glass frame. You can tilt the entire insulation holder out but the insulation is soft and it starts to fall off. Just tilting it enough worked for me. Then I opened up the glass frame from one end, removed the left-over broken piece of the old glass pane and installed the new one in. Then reassemble. The entire process is very easy - but you will need another person for a few minutes when you remove /reinstall the glass frame inside the insulation holder. You would just need a little help holding everything... nothing technical. I would rate the repair technicality at 4 or 5/10. It could even be a 3 if there were less steps involved. Good luck! By the way, Amana/Maytag wanted $70 or so for the glass and then the repair fee. I got the part here for about $50.

removed oven door, removed screws from bottom and sided, door is in layers, removed door layers like taking apart a sanwhich layer by layer, once i got to the inner layer i just had to bend out the little tab on the frame,remove the broken pane and place in the new one, bend the tab back and then put the door back together layer by layer, it was very easy and saved me money, and frustration in dealing with a repair man from a well known company who tried to tell me I needed to replace the whole door as the glass was factory sealed in the door, WELL! this girl's hair may be blonde but not that blonde, I received the glass the very next day, and it took me 40 minutes tops to replace the glass, EASY! KC

Replaced the hinges, the appliance never really shut 100% and after several year it got worse. Now it is perfect and we don't have any problem with heat up time of oven, used to take extra long to get to desired temp. Should have sent it back in the beginning.

I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

Removed old seal by pulling each little metal prongs out from holes in door frame, then positioned new seal by inserting its prongs into holes in door frame, making sure seal is sitting right in place.

needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks

This was an easy repair and the parts fit perfectly. I removed the oven door by unlatching it and sliding it off. I then used a screwdriver to take the back cover off, and took the old hinges off with the screwdriver and replaced them with the two new ones that I ordered. I replaced the back of the door panel and put the screws back in and WA LA - just slid the door back on and tightened the latches.

Removed both oven doors to remove from the wall. Pulled the oven out of the wall. Removed all the sheet metal backing on the back of oven top and bottom. Removed the electrical,connections to the fan. Removed attach,net screws and pulled the fan. A bit of a pain had to twist pull and bend the metal bracket. Replacement fan had to be reversed came apart easily and reversed then reassembled. Fit in easily and attached electrical connections. Then reattached all the sheet metal backing bottom then top. Put oven back in wall then secured in place. Re installed the doors and applied power. Oven worked great as soon as we tested it. Great fix, works better than new!

Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.

pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

Door fell off so removal of door was easy. Removed screws holding the door together to expose hinges. Removed old hinges that were 3 screws for each hinge. Placed new hinges and installed screws then put door halves back together installed screws and then finally replaced door onto the stove. Mission accomplished

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.