The Grate Foot is a black rubber part which attaches underneath the grate in order to protect your stovetop from being scratched, which it does by cushioning the grate on your gas range. If this part ...
This burner cap is for your gas range, and acts as a cover for the burner head. It is black in color and just over 3 inches in diameter. If your old burner cap is damaged or missing, this is the part ...
This is a burner cap for your gas range. The cap acts as a cover for the burner head. If your old burner cap is damaged or missing, this is the part that will replace it. The cap is black in color and...
This is a burner cap for your gas range. The cap is black in color and about 3 inches in diameter. The cap acts as a cover for the burner head. If your old burner cap is damaged or missing, this is th...
This part is the replacement surface burner head for your gas range. It is silver in color and is approximately 3.5 inches in diameter. This burner is sold individually. The burner head distributes ga...
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$80.75
Special Order
Questions And Answers for JGP945SEK2SS
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bill
January 12, 2020
How do i replace the burner control valve
For model number JGP945SEK2SS
Hello Bill and thank you for writing.
Carefully lift off the burner grates and remove all of the burner caps using Phillip's head screwdriver unthread the screws securing
the burner heads disconnect all of the
spark wires from the surface igniters
attached to the heads
now insert a putty knife under the main
top to release the retaining clips
detach the main top and use a quarter
inch wrench to unthread the screw to
release the grounding wire you can now
set the main top aside next remove all
of the burner control knobs unthread the
mounting screws securing the burner
valves to the front manifold panel open
the oven door and remove the screws
securing the bottom of the manifold
the panel now remove the screws on top set
the front manifold panel aside next
unthread the screws to release the
support bracket detach the appropriate
spark switch
use a half-inch wrench to unthread the
nut securing the gas tube to the burner
valve now unthread the screws securing
the mounting clamp and remove the old
valve before you install the new burner
valve confirm that the gasket is intact
align the new valve on the manifold
position the mounting clamp then thread
and tighten the screw attach the gas
tube to the valve then thread and
tighten the nut snap the spark switch
onto the new valve reposition the
support bracket and secure it with the
screws reposition the front manifold
panel replace the mounting screws on top
secure the two mounting screws on the
bottom as well
align the manifold in the panel and
replace the screws to secure the burner
valves replace the burner control knobs
before you reinstall the main top
we recommend inserting the spark wires
in the orifice, holders to secure them
now set the main top on the frame and
secure the grounding wire with the screw
reposition the right side of the main
top first by hooking the rear edge on
the mounting tab so the top is seated
under the vent now position the rear
edge on the left mounting tab making
sure the officeholders protrude through
the holes in the main top snap the front
edge into place when replacing the
burner heads first connect the spark
wires to the surface igniters align the
heads and rethread the screws to secure
replace the burner caps and reposition
the grates with the repair completed. We hope this helps. Please contact us anytime if you require further assistance.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.