JGD8130ADS20 Jenn-Air Cooktop - Overview
Sections of the JGD8130ADS20
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Range Grease Filter
PartSelect #: PS11743846
Manufacturer #: WP707929
This grease filter is almost fourteen inches long and almost twelve inches wide. This filter is intended for use with some downdraft cooktops and ranges.
$49.14
In Stock
Top Burner Igniter
PartSelect #: PS2082000
Manufacturer #: 74004053
This top burner igniter comes with a mounting bracket.
$35.46
In Stock
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$26.58
In Stock
Range Knob
PartSelect #: PS11744699
Manufacturer #: WP7733P314-60
Sold individually. This knob accepts a D-shaped shaft.
$13.73
In Stock
Spark Igniter Set
PartSelect #: PS11744110
Manufacturer #: WP74005890
This part provides the spark to the burners.
$109.71
In Stock
Spark Module - Oven
PartSelect #: PS2094592
Manufacturer #: 8215557
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$168.19
In Stock
Brass Seal
PartSelect #: PS11744111
Manufacturer #: WP74005893
This is the replacement brass seal for your range or cooktop. It is made of brass and is approximately 1 inch in diameter. This part may also be known as the surface burner orifice holder seal. It pre...
$10.18
In Stock
Range Exhaust Vent Blower Wheel
PartSelect #: PS11757592
Manufacturer #: WPY707985
This exhaust vent blower wheel is almost seven inches in diameter, and just under four inches deep. It is made entirely of metal and is used with a range's venting system.
$143.86
In Stock
Burner Head
PartSelect #: PS11741676
Manufacturer #: WP3403M075-29
This range surface burner head is designed to distribute gas evenly through precision ports to create a consistent, stable flame for reliable cooking performance. Featuring a 1/2-inch burner size and ...
$196.13
In Stock
Grill Grate
PartSelect #: PS2078365
Manufacturer #: 71003267
This grill grate is sold individually.
No Longer Available
Fan Switch - Black
PartSelect #: PS3408226
Manufacturer #: W10341820
This may look different than the original, but is a functional equivalent. When installing this part, you may be required to drill holes and file the metal edges to adapt the switch to the original panel.
$304.60
Special Order
Cook Top Base
PartSelect #: PS11738714
Manufacturer #: WP2001F175-09
This sealed-burner gas range cooktop provides a smooth, durable cooking surface designed to contain spills and support grates and burner caps for optimal performance. Its sealed design helps protect i...
$274.02
Special Order
Questions And Answers for JGD8130ADS20
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JGD8130ADS20
[Viewing 4 of 4]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replaced filter
-
ELOISE from MILFORD, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
486 of 513 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old grease filter that I actually did not know I had to change
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen
Parts Used:
-
deborah from fort pierce, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
451 of 540 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gas burner ignitor failure
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
Parts Used:
-
roy from East Providence, RI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
142 of 162 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!