Models > JDR8895AAS

JDR8895AAS Jenn-Air Range - Overview

Sections of the JDR8895AAS

[Viewing 8 of 8]

Manuals & Care Guides for JDR8895AAS

Click to download
Keep searches simple, eg. "belt" or "pump".
Lower Bake Element – Part Number: WP7406P428-60
Lower Bake Element
★★★★★
★★★★★
(76)
PartSelect #: PS11744518
Manufacturer #: WP7406P428-60
This part is located in the lower oven at the bottom.
$65.54
  In Stock
Order within the next 12 hrs and your part ships today!
Long Oven Sensor – Part Number: 12001656
Long Oven Sensor
★★★★★
★★★★★
(21)
PartSelect #: PS1570174
Manufacturer #: 12001656
This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.
$47.67
  In Stock
Order within the next 12 hrs and your part ships today!
LEVELER-FOOT,SCREW,F/S,NYLON – Part Number: W11665456
LEVELER-FOOT,SCREW,F/S,NYLON
★★★★★
★★★★★
(7)
PartSelect #: PS16875974
Manufacturer #: W11665456
This leveling leg is two inches long. It is all black in color and it is made entirely of plastic.
$26.92
  In Stock
Order within the next 12 hrs and your part ships today!
Broil Element - Push On Terminals – Part Number: W10201551
Broil Element - Push On Terminals
★★★★★
★★★★★
(28)
PartSelect #: PS2342087
Manufacturer #: W10201551
This broil element is found on the roof of the oven.
$117.18
  In Stock
Order within the next 12 hrs and your part ships today!
BUMPER – Part Number: W10919249
BUMPER
★★★★★
★★★★★
(1)
PartSelect #: PS11770098
Manufacturer #: W10919249
Sold individually. Must be held in with adhesive.
$17.90
  In Stock
Order within the next 12 hrs and your part ships today!
Bi-Pin Halogen Bulb – Part Number: WP74009925
Bi-Pin Halogen Bulb
★★★★★
★★★★★
(14)
PartSelect #: PS11744355
Manufacturer #: WP74009925
This part is a replacement halogen lamp for your oven. The bulb is 25 watts and 120 volts. If your light bulb is burned out, this is the part that replaces it. Be sure to turn off power to your range ...
$32.75
  In Stock
Order within the next 12 hrs and your part ships today!
Door Gasket – Part Number: WPW10162384
Door Gasket
★★★★★
★★★★★
(19)
PartSelect #: PS11749287
Manufacturer #: WPW10162384
This oven door gasket comes with built in retaining clips.
$118.08
  In Stock
Order within the next 12 hrs and your part ships today!
Burner Knob – Part Number: WP74010205
Burner Knob
★★★★★
★★★★★
(3)
PartSelect #: PS11744380
Manufacturer #: WP74010205
This knob accepts a D-shaped shaft. Sold individually.
$41.34
  In Stock
Order within the next 12 hrs and your part ships today!
Screw – Part Number: W11233072
Screw
★★★★★
★★★★★
(5)
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$26.43
  In Stock
Order within the next 12 hrs and your part ships today!
Upper Bake Element - 240V – Part Number: 74004105
Upper Bake Element - 240V
★★★★★
★★★★★
(8)
PartSelect #: PS2082040
Manufacturer #: 74004105
This bake element is found on the bottom of the oven.
$142.10
  In Stock
Order within the next 12 hrs and your part ships today!
Inner Door Glass Pane – Part Number: 74003645
Inner Door Glass Pane
★★★★★
★★★★★
(15)
PartSelect #: PS2081701
Manufacturer #: 74003645
Glass only.
$138.72
  In Stock
Order within the next 12 hrs and your part ships today!
Oven Rack – Part Number: WP7801P173-60
Oven Rack
★★★★★
★★★★★
(4)
PartSelect #: PS11744745
Manufacturer #: WP7801P173-60
Used in the lower oven. Sold individually.
$122.69
  In Stock
Order within the next 12 hrs and your part ships today!

Questions And Answers for JDR8895AAS

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

8 questions answered by our experts.
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Edward
December 30, 2019
Jenn-aire range purchased november, 2006. Background: After 13 years of perfect service, the lower oven bake element failed, with a pop and a flash, on 12-27-2019. I replaced the element - simple job.This evening (12-30-2019) the cook top gas igniter, or their circuit, failed in that the igniters cannot be turned off. the igniters, one or more, start clicking and sparking at random, whether or not they are being used. the only way i can turn them off is to trip the appropriate circuit breaker in the panel. please consider this, and advise a course of action that will help me get our range back to go. thank you and happy new year' e. n. colburn
For model number JDR8895AAS
PartSelect logo
Hello Edward and thank you for writing. A common cause of igniters clicking constantly is excess moisture in the area. When you're cooking up a storm, pots boil over, sauces spill, stuff happens. This moisture can seep into the area where the igniter PS 11746068 lives and cause it to click when the stove or cooktop is off. However, sometimes one or more of your spark ignition switches PS2004067 can fail. If one of the switches breaks down while the electrical contacts are closed, the switch will send a continuous signal to the spark module, resulting in a burner that keeps sparking continuously. We hope this helps. Please contact us anytime if you require further assistance.

3 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Paul
January 15, 2020
Top right front burner does not ignite. The igniter sparks and there is gas smell present. Took top plate off and a small Flame ignited in the center. All other burners work. Could you please diagnose my issue.
For model number JDR8895AAS
PartSelect logo
Hi Paul, Thank you for your question. If your burner is not igniting, check to see if there is any food debris or a grease build-up that may be clogging it. If there is nothing clogging the burner, check the wires which connect the igniter to the control module. If they are not making a solid connection, you will not get the spark needed to properly ignite the burner. If this checks out fine, you will need to check the igniter switch with harness and the spark module to see if they are working correctly. You will need to test the parts with a multi-meter. Here is a link to one of our videos on YouTube that you may use as a general reference on how to use one, https://www.youtube.com/watch?v=bWC44fHn0As. Both of these parts should test for 120 vac. If they do not, you will need to replace them. We hope this helps. Thank you and have a great day.

Was this helpful?
Thank you for voting!
Jeff
January 31, 2022
The lower bake element went out in lower oven. I ordered a new element, Put new element in oven, and it does not work. Is there any other troubleshooting that should be looked at or could the new element be bad also? All wiring and connections look good in back of oven.
For model number JDR8895AAS
PartSelect logo
Hi Jeff, Thank you for your question. If the bake element is defective, you should first do a visual check. If the element is blistered or separated, then it should be replaced. If the element appears to look normal, then turn the oven on to a bake function for a minute and then turn it off. Check the element for signs of heating and if it is still cold then it may be defective. If the lower bake element shows no visible signs of damage, you will need to test it with a multimeter for continuity. Set your multimeter to the Rx1 setting and touch the probes to the element’s terminals. The exact reading of a functional bake element varies from model to model, but almost all fall somewhere between 19 and 115 ohms of resistance. Refer to your owner’s manual to determine what reading your test should produce. If your element no longer has continuity or is damaged, you will need a replacement bake element. If the bake element is fine, you will need to check the oven temperature sensor, the electronic control board and the wiring between the parts to see which one is causing the issue. Once you have determined the part you need, please feel free to call customer service. We are open 7 days a week and anyone will be happy to assist you. We look forward to hearing from you!

Was this helpful?
Thank you for voting!
Related Parts:
Penny
October 28, 2022
I would like to know when this range was in production
For model number JDR8895AAS
PartSelect logo
Hello Penny, thank you for your question. The manufacturing date is 2004. Good luck with your repair.

Was this helpful?
Thank you for voting!
Donna
November 18, 2022
Top oven comes on and reaches temperature set then red oven temp light starts blinking oven and it shuts down, What can be wrong?
For model number JDR8895AAS
PartSelect logo
Hello Donna, thank you for contacting us. We would recommend testing the upper bake element, part number PS2082040, the lower bake element, part number PS11744518, and the temperature sensor, part number PS1570174, for continuity using a multimeter. If this does not help, the issue is probably related to the control board. Please reach out to customer service if you need help placing an order. Glad to be of help!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
  • 2

Common Symptoms of the JDR8895AAS

[Viewing 11 of 11]
Little to no heat when baking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Element will not heat
Fixed by
these parts
Fixing Fixing Fixing
Show All
Oven not heating evenly
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Little to no heat when broiling
Fixed by
these parts
Fixing Fixing Fixing
Show All
Oven is too hot
Fixed by
these parts
Fixing Fixing Fixing
Show All
Touchpad does not respond
Fixed by
these parts
Fixing Fixing Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing Fixing
Show All
Gas igniter glows, but will not light
Fixed by
these parts
Fixing Fixing
Show All
Will not program
Fixed by
these parts
Fixing
Show All
Door won’t open after self cleaning cycle
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Parts Used:
Long Oven Sensor
  • David from Westford, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
157 of 201 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper broiler element (of upper over) burnt out
This particular model has a bracket that holds the element close to the oven ceiling, so I had to unscrew that as well as the element mounting screws on the back oven wall. The hardest part (not that hard) was the connectors were really tightly clamped to the element terminal. I had to use pliers to help wiggle them off the tips. Recommend doing this very gently yet firmly - I was worried about ruining the connectors or the wires to the oven. The element was deader than dead and actually fell apart in three places once it was detached. The new replacement element arrived a couple days later. Putting it in was a breeze, although the oven is quite dark and I needed Mrs. Handyman to hold a flashlight so I could get the screws in. Oven works fine now.
Parts Used:
Broil Element - Push On Terminals
  • Todd from San Antonio, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
80 of 88 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F1-1 code
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will cause the plastic plug connector to melt from oven heat.
Parts Used:
Long Oven Sensor
  • charles from marstons mills, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
75 of 101 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!