This rear drawer support comes with the installation screw. This part has been redesigned. The new support inserts towards the rear of the drawer as opposed to the side.
This part is also known as the "brains" of the appliance. ***NOTE: The wiring could be different than the original control. This part may need to be installed by an appliance repair person.
This is a replacement haliant element for your cooktop or range. It is used with flat top ranges, and is found under the glass top of the range. This element is approximately 12 inches in diameter and...
This part is a replacement screw for your oven. It is made of black metal and is sold individually. This screw is approximately 1/4 inch in diameter and about 1/2 inch in length. It is designed to con...
$11.80
Special Order
Questions And Answers for JB655EK1ES
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
JOHN
December 26, 2022
need 12"/9" dual burner for this range
For model number JB655EK1ES
Hello John, thank you for your inquiry. The Surface Element for your model is part number PS2321564. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
During preheat convection fan runs for a minute then shuts off doesn’t come back on any information would be appreciated thanks
For model number JB655EK1ES
Hello Alberto, thank you for your question. It may be a clogged vent Tube PS12726086. Test the Temperature Sensor PS10059162 for accuracy. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Or, you may need to replace the Convection Motor PS11773841. Good luck and have a great day.
the element on the stove top comes on but it does not go off i have to turn it off even when i have it set on 3
For model number JB655EK1ES
Hello Eldon, thank you for getting in touch. Based on our research, we would recommend checking the following parts to fix your issue: switch rotary, part number PS11766870, small element switch, part number PS236754, large element switch, part number PS11729102, and control board, part number PS11736355. If you require assistance to place an order, please contact customer service. We hope that helps!
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.
After removing the back of the range the oven control board was visible and accessible by removing four nuts. There was some resistance removing the leads from the oven coils and light-bulb mechanisms but with some leverage and pliers they came loose. The only challenge was the face plate of the unit is attached using adhesive and needed to be carefully peeled off and added to the new oven control board. Getting this right was just a matter of taking time and lining up the components correctly. After applying the face, the new control board went right in. I reattached the back, plugged the unit back in, and the over has worked great for the past week. Part select being able to identify the part numbers listed from the component likely saved me at least $100 of having a GE certified repair technician come in.
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient