This burner bowl is also known as a burner drip bowl or burner drip pan, and is designed for use with your cooktop or range. It is black in color and is approximately 6 inches in diameter. It can be f...
This 40-Watt light bulb is sold individually.
It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges,...
The temperature sensor detects the temperature within the oven cavity. If your oven is too hot, not heating evenly, or has little to no heat when baking, you may need to replace the temperature sensor...
If your stove’s burner isn’t heating right—maybe it’s stuck on high or won’t turn on at all—this control switch could be the fix. It’s made for 6-inch burners and lets you adjust the heat smoothly, no...
This genuine GE drawer support is an original replacement part sourced from the manufacturer and is designed for use with electric ranges. Made of durable plastic, it attaches to the rear of the drawe...
The electronic oven control board manages heating and temperature functions in wall ovens. Modified wiring may require professional installation. Unplug the oven or shut off the circuit breaker before replacing.
This part is the replacement light socket for your oven. The oven light socket provides power to the light, and at the same time holds the light bulb in place.
Looking to fix your range drawer? You're in the right place. First things first, the GE Front Drawer Support is the key to maintaining stability'and without it, your range drawer might wobble or becom...
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Nona
January 26, 2023
Troubleshooting, right front 8 in element overheats. I have exchanged the 8 in elements and it still does it so not the element. Maybe where it plugs in? Can that be replaced?
For model number JB258DM1BB
Hello Nona, Thank you for the great question. This is normally an indication the Switch that controls the Element is faulty and may need to be replaced. Thanks again for your great question!
the burners or oven element only get warm will not go to high
For model number JB258DM1BB
Hi Luis, thank you for contacting us. According to our research, we recommend checking the temperature sensor, part number PS10059162. Locate the sensor on the back of the oven. It is usually near the broil element off to either side. Now disconnect the wires. Next, set the multimeter to the resistance setting and adjust the range if needed. Now touch each probe to each terminal. At room temperature, you should get a resistance of around 1100 ohms. If the reading is significantly off and is under 1000 or over 1200 ohms, then the sensor is faulty and should be replaced. If this does not solve your problem, you may need to replace the surface element control switch, part number PS236754. We hope this is helpful!
Turned off circuit breaker to range. Removed the 2 oven racks. Removed two screws in back of oven compartment. Pulled element forward and the terminal connections get exposed. The right terminal clip disconnected by itself and the wire went back into the stove and could not be retrieved. Removed range draw under the oven and pulled entire range out from wall about 4 feet.. Removed metal backing with a socket wrench and exposed the oven element wires and terminals. Reinstalled new element and metal backing. Since range was out from wall, cleaned and vacuumed before pushing stove back in place. Since range draw was out re-leveled by setting adjustable feet. Reinstalled drawer and racks. Turned on circuit breaker. Tested element by setting bake cycle on.
After the element cooled down, I pulled the racks out of the oven, turned off the oven at the breaker box, then, using a nut driver, loosened the screws that held the baking assembly in the back of the oven, and pulled the connecting wires off. I bent the wires to make sure they would stay out, because if they get back in the insulation, they are hard to find. I would recommend getting a pair of locking pliers and putting them on the ends of the wires just to keep them from getting back into the insulation. Then I attached the left connection wire and then the right one, pushed them back into the insulation, tightened the baking assembly to the back wall of the oven, turned it back on at the breaker box, then tested the oven to see if it heated up. It did. Total repair time 15 -20 minutes. Would have been less if I didn't have to chase one of the wires back in the insulation. Shamless plug for the company ...By paying extra for 2-day shipping to receive the part, I saved just over $20 from buying it at Sears, which would have had to order the part anyway.
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.
