HDA2100H70WW General Electric Dishwasher - Instructions

Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.

The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.

This was a fairly simple repair. After disconnecting power to the dishwasher and removing the panel below the door, first had to remove a retainer C clip from the gate valve shaft. Then disconnected the linkage from the gate valve solenoid, removed two return springs and slid the gate valve contol arm off the shaft. Then removed the solenoid bracket that was fastened to the housing by 2 screws. This allowed access to the push on nut on the valve shaft. Removed the old push on nut which exposed the leaking seal. Removed the bad seal, then moistened and carefully slid on and seated the new drain valve shaft seal. Affixed new push on nut. Reinstalled the above mentioned parts that were removed. Problem solved - no more leak. Total cost $18.81 for factory GE parts plus $6.95 shipping. Thank you PartSelect.

First off on this model, if one of the telescopic spray arm weld assembly comes out it is NOT repairable you have to replace the whole part.
The assembly on my model number was simple you do NOT have to PRY anything out...(I broke the base spray arm trying to shove a screw driver into the Spray arm weld.(You could try this but chances are the plastic will break and I recommend replacing both parts why not???.)
There are two bolts on the sump protector basket that has to be removed first. They are 1/4 inch.
Once that cover is free there is a bolt (also 1/4 inch) on the base spray arm it is easy to see but hard to get to I used a very thin open ended wrench
1/3 turn at a time till I could get the socket on it.
Next there is a rubber gromet like thingy that just pulls loose remove it also.
Next take the spanner wrench (I used one with a rubber belt) wrap around base spray arm and turn counter clockwise it just unscrews.

reassembly is simple but this is GE so I inspected the sump and found one medal impeller and one black screw at the bottom!!!!!
The impeller is threaded and just screws onto the shaft (look at the diagrams on this web site to see placement.)
Throw the screw away it does nothing except if left there jacks up the impeller I am guessing it fell out of some factory workers pocket.
If after you put all the parts back in and the washer does not drain check your reassembly if you don't line the parts up just right the unit will not drain.
Don't forget the rubber grommet (not sure what it does but it's easy to replace after all is assembled) also there is a metal washer that is inbetween the base spray arm and the spray arm weld put it back before you click those two parts together it protect the plastic from wearing it is a bearing!!
If you found this site you are doing really good This site had all the diagrams I was looking for I love you guys you so rock!!! I wish the diagrams were bigger but they were adequate. GE 's site was no help and I doubt I will ever buy another one from them.
Good luck just remember look at the parts diagrams before attempting the repair.

replaced rack, no repairs required

I looked at the gasket for the door, and noticed that it was flattened out and also noticed that there were two other seals at the lower left and right corners that were also hard and flattened. I found the parts for my dishwasher on this site and ordered them. Once I received them, I removed the old ones. They just came right out, and I inserted the new ones in the same spot. It was then that I noticed that there is another gasket for the door, that goes at the bottom of the inside of the door. The gasket for the door goes all the way around the outside, except for about a 4 inch section at the bottom of the door, right in the middle. I realized that I probably needed to get a new one of those too, so I ordered that part. I am now waiting on that small, 4 inch door gasket.

Opened package from Parts Select.
Removed Silverware basket from package.
Opened Dishwasher.
Inserted Silverware Basket in rack.
Closed Dishwasher.
Discarded shipping package.
Told wife I fixed Dishwasher.
Sat down & had a beer.

Siimply removed the rack and replaced the wheel assembly. Very easy

First I removed the dishwasher from underneath the countertop and laid it on its back. I used a nut driver to remove the pump support wire and the two clamps holding the rubber connectors to the pump. It helped to hook the pump support wire in a hole in the left side of the frame and reconnect it to the pump to hold it up out of the way. I was able to remove the rubber connector by hand and unscrew it. To install the new rubber connector tightly, I slipped a piece of 2" PVC pipe (outside diameter is 2-3/8") inside the connector and tightened the clamp around the connector and PVC pipe. This allowed me to use the pipe to tighten the rubber connector. I reassembled the dishwasher pump and connections and put the dishwasher back into service

Simply discarded old wheel assembly and snapped new wheel assembly in place. Very simple.

Repair easy. . Snap it in. . . . . . Impressed with the speedy delivery. Thanks

It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!

I read all the other repairs first to find out what I had to do. I then took front cover off the bottom of dishwasher. Identified the leak was coming from drain seal. I shut breaker off unpluged wires that were hooked to the drain valve sensor. removed the clip carfully as not to damage it. Removed srews that held down drain valve. removed the push on nut that holds drain seal in place. then removed old seal. I wiped down shaft to get ride of any corrosion and reinstalled new seal with deep socket and a srew driver. I installed new push on nut with another size socket. I fitted drain valve to shaft, used plyers to gently to pull shaft so I could put the c clip back onto grove on the shaft. reinstalled spring and plug wires back in turned breaker back on. I turned the dishwasher on and it did not leak. I was very happy that i did not have to take the dishwasher out. I did all repairs with everything still hooked up.

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

Ordered the part, by using the diagram on the ge website identified the part and ordered it right them and when it came (delivered really fast) took it out of the bag and screwed it in the jet dry despenser and is working great.