Your washer uses 4 tub dampening straps. It is recommended to replace all 4 at the same time. They keep the tub in the center of the cabinet and are sold individually.
The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably ...
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you...
This is a water pressure switch hose, also known as the air dome tube, for your washer. It is made of clear plastic and is sold individually. The hose transports water to your water pressure switch, s...
This replacement inlet drain hose connects your washer's water pump to its tub. This hose is seven and a half inches in length and only two inches wide.
This part is a replacement socket rod support for your washer. The socket rod support is found at the top of the washer frame in the front part of the washer. It supports the suspension rod, so the ro...
$16.08
Special Order
Questions And Answers for GTWN4950L1WS
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Randy
November 30, 2019
How many cftc is this washer?
For model number GTWN4950L1WS
Hello Randy and thanks for writing.
For your convenience, we have attached the link to the manual. We hope this helps. Please contact us anytime.
https://partselectcom.azureedge.net/assets/manuals/65CB4EB9D4B915B6D42684E47CEA916463F6D6D9.pdf
https://partselectcom.azureedge.net/assets/manuals/1CA3DB67122E35E5E0D9F3FF66E8735BA945D0CE.pdf
Was this helpful?
Thank you for voting!
Kim
August 18, 2021
My washer makes an awful sound like the tub maybe unbalanced ?? worked right on light load only for awhile but now makes noise again . plus washer shakes . thank you for any info.
For model number GTWN4950L1WS
Hello Kim, thank you for writing. The Tub Dampening straps PartSelect Number PS271100 support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves or is making a loud banging noise during the wash cycle, the washing machine tub could be off-balance, meaning one or more of these straps may be loose, or broken. This Tub Bearing PartSelect Number PS271510 goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you may need to replace the tub bearing. Good luck with your repair.
When machine goes into agitate it makes a loud grinding noise. Machine is not that old and it is never filled when using.
Any ideas as to what it could be ?
For model number GTWN4950L1WS
Hi Rick, thank you for reaching out. Based on the description that you have provided, we would recommend checking the following parts: tub bearing, part number PS271510, mode shifter assembly, part number PS2354082, hub nut, part number PS271505, and drive pulley, part number PS1482349. We hope this sorts out your problem!
My old pump is different from the new one my old has two rubber gusset to hold it while the new part number wh23x10030 has holes for screws and the electrical connections are different as well.
For model number GTWN4950L1WS
Hello Armando, thank you for getting in touch. To replace the pump, follow the instructions in the attached video link. We hope this sorts out your problem!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor) 2. Removed the 2 bolts holding the Pump/Motor assembly to the machine. 3. Removed both hose clamps on the Pump/Motor assembly and removed Pump. 4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps. 5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump. 6. Plugged in the washing machine and everything worked.
NOTES: 1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine. 2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.
Aside from getting the wet clothes and most of the water out,the toughest part of the job for me was to figure out how to get inside the machine. I nearly wrecked the thing trying to lift the top panel. After some frustration I removed the star-type screws on back of the control panel and found, tucked away neatly, the documentation/parts list complete with instructions on how to remove the FRONT panel. Once I got inside it was easy to locate the pump. I ran the drain cycle for a moment to see if the pump turned at all. The original had an exposed fan so it was easy to see that indeed the motor was not turning. I inspected all the hose and electrical connections to make sure I had the tools I'd need and the savvy to replace the part(s) if I could locate them. I'm not much of a web-head, so I was a little surprised when I typed G.E. appliances and the search took me to partselect.com where I was pretty much coached through the procedure before I even ordered the part. The box arrived ahead of schedule (yay) and when I looked at the pump it didn't look much like the one I was replacing. But then I realized it was the same thing just ten years more advanced. I used a small pair of vise grips to pinch and lock the pipe clamps open. I know there is a plier made for this, but... Anyways, after loosening the clamps and sliding them away from the pump I pulled the hoses off and let the last of the rinse water still in them run down my shirt sleeve to my elbow. (optional, not recommended) Thus refreshed I then rummaged through my socket set and found what I needed to remove the 2 sheet metal mounting screws and disconnected the 2 power leads. I removed the faulty pump and proudly showed it to my wife. Unimpressed, she asked how much longer. I quickly reversed the procedure to install the new unit and confidently piled in a load of laundry. The cycle completed just fine and has done so since. I will and have recommmended partselect.com to friends and will use it again for sure.