This lid lock, also referred to as a door lock, is a genuine replacement component designed to secure the washing machine lid during operation. It ensures the appliance recognizes when the lid is prop...
This suspension rod and spring assembly is a manufacturer-approved replacement part designed to stabilize the washer tub during operation. Positioned on the left side of the machine, it is one of four...
This inlet valve is designed for use in compatible top-load washing machines and plays a key role in regulating water flow during the wash cycle. Controlled by electrical signals, the valve opens and ...
Are you struggling with a malfunctioning washing machine? We have just the solution you need'the GE Drain Hose. This simple but essential part is tailor-made for washing machines, tasked with safely d...
Having trouble with your GE washer? Our Nut Hub could be just the solution you need. This little device has a big job ? it tightly secures your washer hub to the gear case shaft. Its accuracy helps yo...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
9 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
November 17, 2022
looking to see if this washer has a filter, if so where is it located
For model number GTW685BSL0WS
Hi David, thank you for contacting us. Your model does not have any filter. We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
PHILLIP
October 21, 2024
I HAVE AN GE WASHER WAS WORKING FINE THAN IT STOP DRAINING AND SPINING THE DOOR LOCKS AND THE INTERFACE BOARD SHOW 11 MIN AND COUNTS DOWN TO 9 SEC AND DOES NOT START THE DRAIN AND SPIN CYCLE WHAT MAY I POSSIBLY CHECK TO REPAIR WASHER
For model number GTW685BSL0WS
Hello Phillip, Thank you for your inquiry. Researching your model, we would recommend checking the speed sensor, the mode shifter, and the drain pump. You can test the parts with a multimeter. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lance
August 18, 2025
Super loud when spinning, almost like a worn bearing or something.
For model number GTW685BSL0WS
Hello Lance, thank you for getting in touch. Check the drive transmission or gear case assembly, part number PS16729511. It might be worn out or defective. They have gears in them which can fail, causing the washer to be noisy during operation. Check the drive pulley, part number PS16554753. The drive pulley makes the connection between the transmission and the inner tub. If the pulley is worn out, the washer will make loud noises. You will also need to check the drive belt, part number PS11736832. The belt gets loose over time due to damage or wear and tear, which can cause loud noise. We hope this helps.
I just replaced the water valve assembly because water was dripping non stop into the tub but now the tub is over-filling and says h20 supply and then drains out. Water no longer drips into the tub though...
For model number GTW685BSL0WS
Hello Lesley,
Thank you for your question. We suggest using a multi-meter to check the water valve you ordered from us to make sure it isn't defective. Typically if the washer is overflowing or if there is a leak its both caused by the valve itself since it controls the water output. We hope this helps.
Softner dispenser fails to dispense. I cleaned the inside same under the cap.
For model number GTW685BSL0WS
Hello Don, thank you for your question. We have researched your model and found that the issue is probably with the water inlet valve, part number PS12171559. The dispenser utilizes water from the inlet valve to flush out the detergent and fabric softener. Slow water flow will cause the dispenser to not distribute the detergent and softener properly. If you require assistance placing an order, please contact customer service. We hope that helps!
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps from pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Removed the control panel back plate cover. Removed the 3 screws that held the water control valve in place. I then unplugged each solenoid one at a time and plugged it into the new control valve. Once all wires were transferred, I pulled the old valve up and put the new valve on. Then reinstalled the screws that held it down and reinstalled the cover plate. Very simple job !
