Models > GSC702-02 > Instructions

GSC702-02 General Electric Dishwasher - Instructions

All Instructions for the GSC702-02
1 - 15 of 24
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Insufficient fill water, dishes not getting clean (valve diaphram had ruptured)
1. Remove lower cover skirt.
2. Shut of water at undersink valve.
3. Unplug power cord or turn off circuit breaker.
4. Disconnect water supply line from fill valve.
5. Unplug the electrical connector from the valve.
6. Remove the 2 valve mounting bracket screws.
7. With loose valve in hand, rotate to gain access to allow release of outlet hose clamp for hose removal.
8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.

Install new valve by reversing the procedure.
Parts Used:
Dishwasher Water Inlet Valve
  • Don from Mount Vernon, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench set
71 of 77 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost Despenser Lid, Droped It And Havent Seen It Since.
Ordered the part, by using the diagram on the ge website identified the part and ordered it right them and when it came (delivered really fast) took it out of the bag and screwed it in the jet dry despenser and is working great.
Parts Used:
Rinse Aid Fill Cap
  • ANNE from SWANNANOA, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
26 of 32 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Little/no water coming in & dirty dishes
1. Remove access panel under door. 2.Shut off hot water.3. Shut off electric to washer.4. Disconnect water line from water inlet valve.5. Remove small outlet water line from valve. Replace valve & reconnect. OR !!! 1.Take solenoid valve & bracket off of original inlet valve 2. Pull out white plastic diaphragm cover. 3. Remove diaphragm & clean out water holes with a pin. 4. Reassemble valve. 5. Reinstall original water inlet valve & save $27.00
Parts Used:
Dishwasher Water Inlet Valve
  • William from Polson, MT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set, Wrench (Adjustable)
17 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace rinse aid fill cap
Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.
Parts Used:
Rinse Aid Fill Cap
  • Judy from Salem, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
8 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
threads broke on rinse aid fill cap
Replaced with a new rinse aid fill cap.
Parts Used:
Rinse Aid Fill Cap
  • Russell from Columbia, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thanks for sending the correct part. You guys did a great job.
Just put the part on.
Parts Used:
Dishwasher Water Inlet Valve
  • Albert from Dallas, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Socket set, Wrench set
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dispenser cap would not stay in place because it had melted
First I opened the package and screwed the new dispenser cap into place.
Parts Used:
Rinse Aid Fill Cap
  • Patricia from Clifton, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rinse Aid Fill Cap melted because it landed next to the heating element because it wasn't screwed in
Simply screwed in new cap
Parts Used:
Rinse Aid Fill Cap
  • Helen from Carol Stream, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Damaged rinse agent dispenser
Unscrewed old one and installed the new one.
Parts Used:
Rinse Aid Fill Cap
  • Ralph from McMinnville, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
7 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
New home to me. Part lost
Put on a new cap.
Parts Used:
Rinse Aid Fill Cap
  • Harry from SAINT LOUIS, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No water during wash cycle.
Shut off water, disconnect power,remove
Faulty valve,install replacement part.
Parts Used:
Dishwasher Water Inlet Valve
  • Jason from Porterfield, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
5 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no a/c
removed relay and replaced, found moth cacoon inside relay. Goodman a/c not3m no goodman in list
Parts Used:
Dishwasher Water Inlet Valve
  • joseph from wall, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Threads on the cap broken
A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.
Parts Used:
Rinse Aid Fill Cap
  • Martie from FULTON, MO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fill Cap Just Keep Turning, Not Locking In Place
I Just Open Door And Put Fill Cap In And Turn That It
Parts Used:
Rinse Aid Fill Cap
  • Broggie from Burlington, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
6 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rinse Aid Fill Cap missing from dishwasher in condo I just bought.
Opened package, removed cap and screwed it in place.
Parts Used:
Rinse Aid Fill Cap
  • Harry from Franklin, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GSC702-02
1 - 15 of 24
Back to Top