This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
The rear drum support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. If your dryer is ...
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
This dryer lint screen is for laundry centers.
Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer.
Follow the instructions in the owner's manual when installing this part.
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
If your washer isn’t filling properly, leaking, or not cleaning clothes like it should, the water inlet valve might be the issue. This part controls how hot and cold water flows into your machine. It’...
$168.59
In Stock
Questions And Answers for GLET1041AS1
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gordon
July 5, 2021
When the washer enters the spin cycle it starts to shake and it sounds like it is spinning hammers. Do you stock parts for this washer/dryer combination and if so can you recommend a repair company in Richmond bc Canada?
For model number GLET1041AS1
Hello Gordon, Thank you for the question. Normally this indicates the Trunnion or the Springs are damaged or broken and may need to be replaced. We do not provide or recommend a Repair Service sorry. We suggest contacting Frigidaire directly. We hope this helps!
WHAT SIZE IS THE WASHER/DRYER - I THINK IT IS 70' HIGH AND 27' INCHES WIDE. BUT WHAT SIZE CAPACITY FOR THEWASHER AND DRYER???
THANK YOU
For model number GLET1041AS1
Hi Lois, thank you for contacting us. According to our research, the dimensions of your model are approximately: height: 75.5 inches, width: 27 inches, depth of the dryer: 25.25 inches, and depth of the washer: 30.81 inches. The drum capacity of your model is 5.7 Cu. Ft. We hope this helps!
Was this helpful?
Thank you for voting!
Lois
January 18, 2024
WHAT CAPACITY IS THIS MODEL?
For model number GLET1041AS1
Hello Lois, thank you for asking. According to our research, the drum capacity of your model is 5.7 Cu. Ft. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
selected correct replacement knob. used small screw driver to remove small black metal sleeve from switch shaft. (had left that in place to be able to turn on dryer with needle nose pliers while waiting on knob). aligned flat of new knob with switch shaft and gently pressed into place.
Googled dryer start knob, Part Select was second site I clicked on, found within 1 min, part was inexpensive, easy to order, arrived quickly and fit perfectly. Excellent online ordering experience.
well, i started at the top and worked my way down. by taking the top off, it gave me more room to get the dryer tub out. took the two screw`s out of the vented plate on the back of the machine to undo the belt. this is a stackable washer-dryer combo, so next i took off the white plate on front between washer & dryer. took off the control panel, unpluged it, then took dryer door front off. then removed the two screw`s that hold that bracket on ,in the back of dryer, pulled the drum out & replaced the belt, but before replacing anything i took the shopvac to it , there was alot of lint in there.when replacing the Grounding Ball Clip & Grounding Ball, i took a one inch by two inch magnet and used it to hold the Grounding Ball & Clip in place so i could get the two screws started in the Drum Support Bearing & Bearing Bracket. after installing that i put the shaft in place & lined the dryer tub up with the 3 screw hole`s ,and boom, bang, pow...nothing to it. it`s easy...parts came very fast....Thx PartsSelect.com...i`ve told all my friend`s about PartsSelect
