GLD4468R10SS General Electric Dishwasher - Overview
Sections of the GLD4468R10SS
[Viewing 5 of 5]
Manuals & Care Guides for GLD4468R10SS
Click to downloadKeep searches simple, eg. "belt" or "pump".
Lower Rack Wheel Kit - 8 Pack
PartSelect #: PS11726733
Manufacturer #: WD35X21038
If your dishwasher door will not close, is noisy when operating, or the dishes are not cleaning properly, you might need to replace one or more of the wheels. Each wheel and axle are made of plastic a...
$59.57
Special Order
Single Lower Wheel Stud/Axle
PartSelect #: PS2353872
Manufacturer #: WD12X10278
Sold individually. This is just the axle that holds the wheel in place on the dishrack. The wheel is sold separately.
No Longer Available
Dishwasher Basket Assembly Silverware
PartSelect #: PS12703061
Manufacturer #: WD28X24469
This basket is part of a silverware basket that has 3 sections. This is the middle section of the basket.
No Longer Available
Silverware Basket
PartSelect #: PS959351
Manufacturer #: WD28X10128
This is a basket for washing flatware or silverware in your dishwasher.
$73.00
Special Order
Dishwasher Dishrack Rollers and Axles
PartSelect #: PS11721505
Manufacturer #: WD35X20994
This is a kit of 4 which includes the wheels and axels.
No Longer Available
Dishwasher Rack Slide End Cap
PartSelect #: PS2370502
Manufacturer #: WD12X10304
The Rack Slide End Cap is a white one-inch plastic part which replaces the end cap for your dishwasher rack, preventing your rack from sliding too far. If you find the dish rack is causing the door to...
$105.18
Special Order
Water Inlet Valve
PartSelect #: PS3654179
Manufacturer #: WD15X10014
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve open and close according to the desired amount of water needed.
$85.06
Special Order
Pump Connector
PartSelect #: PS259530
Manufacturer #: WD18X10010
The circulation pump adapter, or pump adapter assembly connects the circulation pump to the tub of your dishwasher. If your dishwasher is leaking around this adapter, check the connection to ensure ev...
$62.10
Special Order
Door Handle Actuator
PartSelect #: PS2337860
Manufacturer #: WD13X10045
This is a handle actuator for your dishwasher. It is made of black plastic, and is sold individually. The handle actuator is found in the control panel, and it releases the door latch when you lift th...
$98.04
Special Order
Switch Interlock
PartSelect #: PS1021382
Manufacturer #: WD21X10224
This switch interlock is found on your dishwasher door, and it must be actuated for the dishwasher to start. If your dishwasher door does not close properly, or if the machine will not start, you may ...
$31.65
Special Order
Fine Filter
PartSelect #: PS958919
Manufacturer #: WD12X10109
This filter sits at the bottom of the dishwasher.
$120.20
Special Order
Fine Filter Hub Nut
PartSelect #: PS259078
Manufacturer #: WD12X10061
This is the replacement fine filter hub nut for your dishwasher. It is made of white plastic and is approximately 3 inches in diameter. The fine filter hub nut is also known as the lower spray arm hub...
$67.38
Special Order
Questions And Answers for GLD4468R10SS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the GLD4468R10SS
[Viewing 10 of 10]Leaking
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lower rack wheel was melted
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
Parts Used:
-
Mark from Huntingdon Valley, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
523 of 550 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The rear wheels were missing on the lower rack.
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.
Parts Used:
-
Teresa from Phenix City, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
475 of 489 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
soap door latch broken, wouldn't hold soap for later release in middle of cycle like it was supposed to.
Turned off power to unit, 'cuz it has a solenoid lead to open the soap door.
Removed the phillips head screws that held the door together. The screw are located on the inside edge of the door, there are 10-12 of them.
Spearated the door shells carefully, trying not to disturb the location of the wiring in the middle of the door.
Found the 4 screws that hold the module assembly to the door from the inside, and removed them.
Popped the assembly out, cleaned the gasket-seat area and placed the new one in place.
Carefully tightened the 4 screws. It is easy to over-tighten them, so only turn them until you feel they are snug. Let the gasket do the work.
Attached the two solenoid control wires in the same positions they were in before they were removed from the old assembly.
Re-assembled the door halves, again taking care to not over-tighten the phillips-head screws. One got "spun" and I removed it and re-set it into some epoxy.
Returned power to the dishwasher, and stopped washing dishes by hand.
Note: the latch is now made with a plastic that is more dense, and likely will not fail as soon as the original one did. I think GE learned something about the durability of their component plastics since this was originally built.
Removed the phillips head screws that held the door together. The screw are located on the inside edge of the door, there are 10-12 of them.
Spearated the door shells carefully, trying not to disturb the location of the wiring in the middle of the door.
Found the 4 screws that hold the module assembly to the door from the inside, and removed them.
Popped the assembly out, cleaned the gasket-seat area and placed the new one in place.
Carefully tightened the 4 screws. It is easy to over-tighten them, so only turn them until you feel they are snug. Let the gasket do the work.
Attached the two solenoid control wires in the same positions they were in before they were removed from the old assembly.
Re-assembled the door halves, again taking care to not over-tighten the phillips-head screws. One got "spun" and I removed it and re-set it into some epoxy.
Returned power to the dishwasher, and stopped washing dishes by hand.
Note: the latch is now made with a plastic that is more dense, and likely will not fail as soon as the original one did. I think GE learned something about the durability of their component plastics since this was originally built.
Parts Used:
-
James from Naperville, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
100 of 108 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!