GHDA880B-01 General Electric Dishwasher - Instructions

1. Remove lower cover skirt.
2. Shut of water at undersink valve.
3. Unplug power cord or turn off circuit breaker.
4. Disconnect water supply line from fill valve.
5. Unplug the electrical connector from the valve.
6. Remove the 2 valve mounting bracket screws.
7. With loose valve in hand, rotate to gain access to allow release of outlet hose clamp for hose removal.
8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.

Install new valve by reversing the procedure.

Opened package from Parts Select.
Removed Silverware basket from package.
Opened Dishwasher.
Inserted Silverware Basket in rack.
Closed Dishwasher.
Discarded shipping package.
Told wife I fixed Dishwasher.
Sat down & had a beer.

1. Remove access panel under door. 2.Shut off hot water.3. Shut off electric to washer.4. Disconnect water line from water inlet valve.5. Remove small outlet water line from valve. Replace valve & reconnect. OR !!! 1.Take solenoid valve & bracket off of original inlet valve 2. Pull out white plastic diaphragm cover. 3. Remove diaphragm & clean out water holes with a pin. 4. Reassemble valve. 5. Reinstall original water inlet valve & save $27.00

Just put the part on.

I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket.
I was very happy the the service.
Donald Brown

Shut off water, disconnect power,remove
Faulty valve,install replacement part.

Removed old basket, put new one in. New basket fits but it is larger then the old one so it takes up more room leaving less room for dishes. My dishwasher is apartment size.

Service from PartsSelect was very prompt.

removed relay and replaced, found moth cacoon inside relay. Goodman a/c not3m no goodman in list

Took out old one and put in the new one. Not hard at all. Thanks

Pulled out old basket with holes at bottom and replaced it with new basket. Perfect fit!

Opened the box the new silverware basket came in and replaced the broken one.m

Simply took out old and put in new

This is erins dad. She just bought her first home and it was missing the basket. I went online found your company and ordered.

Just plopped it in, it fit perfectly! I love it! Very easy to order the part, and very fast shipping! I order it and it took a day to get to me!

Remove lower panels, turn off hot water supply, Turn off breaker to dishwasher. notice how power connector is orientated and how valve is mounted to chassis of dishwasher and remove Molex connector which supplies power to valve. The power to the valve is 120VAC when the timer gets to the appropiate cycle I measured the valve with no connector attached with DVM set to Diode or ohms setting and got about .825. I measured the NEW part and measure about the same. Have towel under valve hoses for small amount of water will come out. remove small diameter hose , inlet water supply, remove 2 screws holding part with nutdriver to remove valve which exposes the black hose attached to valve. Hose has a hose clamp, use pliers to remove. good time to check and clean hoses. I unwrapped a coat hanger to run through the hoses for debris. to INSTALL reverse the above. clean water away from floor with towel. Turn on hot water supply, check for leaks, I did not have any leaks. Turn on breaker. You can stick a stubby screwdriver into the door close switch of front door which enables you to turn on (swing arm) dishwasher with door open to check water pressure. I have a great deal more water pressure and water from jets spray much higher than before. Old valve was clearly bad, but solenoid of valve still worked, which sucks in the arm when energized. I used a DVM on the 2 wire connector on valve to check for 120vac when cycle turns it on-measured good. I still don't have quite the same cleaning as before. It is 80% better, but something is still not right. My wife put in one of those pot cleaners (red) mesh plastic thingy on top rack--and found pieces of red mesh plastic in debris area, cleaned it out as best I could removing the 2 covers, but not sure valve is opening there or debris is clogged in there which sends pieces of food, etc. through hose to garbage disposal. Hose wasn't clogged. Cleaning better but wife is still saying not as good. The Pump is running good, cleaned dust and dirt out of pump with vacuum. 10 years old, thinking of removing dishwasher from counter and checking the pump area or change it.