This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This part is the replacement door plunger or door strike for your washer. It is made of white plastic and is approximately 2 inches by 1.5 inches. The door strike attaches to the washer door and activ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
December 7, 2019
Washer stops i mid cycle and have to push start button again.Is it the door lock switch
For model number GFWH2400L0WW
Hello Mike, thank you for your question. Yes, that would be the first part we would recommend testing/replacing. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Charles
May 5, 2022
Washer sounds louder than usual when in spin mode
For model number GFWH2400L0WW
Hi Charles,
Thank you for your question. If the washer makes a loud noise when it spins, the tub bearing is likely worn or damaged and it will need to be replaced. The bearing is part of the rear tub assembly. The part number listed under your model number for the rear tub assembly is PS11729508. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Albert
June 9, 2023
Machine has power, but eill not turn on ?
For model number GFWH2400L0WW
Hello Albert, thank you for contacting us. We have researched the model and would suggest checking the door lock assembly, part number PS1021459. A damaged or broken door lock might be causing the door to not close properly, resulting in the washer not starting. You may also check the electrical continuity of the door lock using a multimeter. We hope this helps!
I hit start on my washer and it just sits and clicks won’t start, sometimes it will say door locked then spin 2 times then stop and door unlocks, I retry and it sits and clicks again
For model number GFWH2400L0WW
Hi Alisia, thank you for reaching out to PartSelect. We believe your washer is having this problem because of a faulty door latch, part number PS1021459. Good luck with your repair!
Hi James, thank you for getting in touch. We would suggest checking the drain hose for any blockage first. If it is fine, the issue could be with the drain pump, part number PS16743374. It removes water from the washer during the drain portion of the cycle. You may need to replace it to fix the issue. We hope this solves your problem!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I Disconnected power to machine and shut off water supply lines. Move washer away from wall and removed supply lines.(good time to replace them if older than five years) Where these supply lines attach to the washer is the water valve you are replacing. There are 3 screws on the back of the cabinet lid, then on the front 3 more screws hold the lid to the plastic control housing. After removing screws you need to slide the lid up and towards the back of the machine app. 1 1/2"to 2" before you can raise the lid up and off of the machine. Once the lid is off it is just one screw holding the valve, and a hose clamp that needs removed from the end of the valve. Then slide valve to the right (looking from front of machine to the back.) I left the wires attached to the old valve,installed the new valve then reattached the wires in the same order as they were on the old valve to avoid confusion. (note valve must slide into place to get screw to line up.)assemble is reverse of the above steps. Don't forget to level machine. Be careful attaching water supply lines plastic valve threads can strip without much effort.
I unplugged the power cord from the wall outlet, then I had to remove the top panel off the machine by removing the three phillips screws holding the back trim strip to the front top of the machine, than I removed the three 1/4 inch head screws holding the top panel found at the back top of machine. I now pulled the top pannel to the rear and removed the top pannel. Then I used pliers to squeeze open and slide clear the small clamp to the rubber hose to the valve and removed the hose end to the valve. Then I carefully pulled off the four wire connectors to the two solenoids of the valve. Than I removed the one 1/4 inch head screw found on the back side of the machine securing the valve to the machine. Then I removed the valve by sliding it to the mounting screw side to disengage it. Install the valve in reverse order but I tightened the valve holding screw only till it's seated because it screws into soft plastic. 6/15/08
Remove bottom kick plate of washer. Remove 4 screws behind door that hold the latch/lock assembly. Reach up inside the washer from underneath to unplug 3 wire connectors. (This is a very tight spot). Once wires are off, part comes right out. Connect wires to the new part - this is by far the most difficult part of the job because it is way up inside the washer. Replace all bolts. Overall, pretty easy to do - just reconnecting the wires is a pain, but if you are patient it is not a big deal.
