Ask our experts a question about this model and we'll get back to you as soon as possible!
21 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brice
July 23, 2021
How to remove the tub baffle
For model number GFW450SSM1WW
Hi Brice,
Thank you for your question. Here is a link to one of our YouTube videos that you may reference on how to install the tub baffle, https://www.youtube.com/watch?v=7UEKr8SMZWM. The washer in the video may be different from yours, but it will give you a general idea on how to install the part. We hope this helps! Good luck with the repair!
Hello Mathew, Thank you for the question. If the Tub spins on the last drain and spin cycle but not for the rinse cycle, you may have a defective User Interface Board. The board controls the cycles and it maybe skipping or not proceeding to the Spin cycle. We hope this helps!
I am looking for the rubber gasket for this washer. It’s the one as soon as you open the door
For model number GFW450SSM1WW
Hello Robert, Thank you for your inquiry. We have researched the model you have provided and have found the part you are looking for is PS11763264. We hope this helps you.
Why is the fabric softener compartment still have water in the reservoir after washer has finish?
For model number GFW450SSM1WW
Hello Susie, Thank you for the question. Normally this is caused by a blocked Dispenser from a soap build up. We suggest removing the dispenser and cleaning it out. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jimi
April 26, 2023
How do I remount the two suspension springs for the tub? One has fallen off.
For model number GFW450SSM1WW
Hello Jimi, thank you for the question. Based on our research, we are providing you with instructions that will help you remount the suspension spring.
1- Unthread all the screws to remove the top panel.
2- Now, you have access to the suspension springs.
3- Hook the spring into the tub.
4- Get the rope onto the spring, lift it up to the same place, and hook it up to the frame.
5- After hooking up, pull the rope out.
We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed three 7mm sheet metal screws from the bottom front panel. The drain pump is in the front right. Removed the manual drain screen to drain residual water from the system. A bucket was necessary to collect all the water. Disconnected the inlet and outlet hose. Disconnected the electric supply. Removed two Phillips screws holding the pump to the bottom of the machine. Slid the pump towards the rear to clear the support pegs and removed it from the front opening. Installation is the reverse of those steps.
2 things to note if you’re going to replace this part. First, you definitely need the 6” crescent wrench as noted in the instructions. Second, tape up the flanges of the machine so you don’t cut your arms to pieces on sharp metal edges.
First I locked out the power cord. I pulled the back screws to the top panel off, slid the top panel to the back of the washer, and pulled the top off. opened the washer door, and ran my down where the door switch was. with one hand on the switch, I use the other hand with a philips screw driver to remove the screws on the door switch. Pulled the switch up just enough to remove the electrical plug. Now installation will be the same but start backwards. Plug in the switch, run the switch into the housing. While holding the switch in place with one hand use the other hand to install the two screws. Replace the top panel, remove any lockouts.