Your washer uses 4 tub dampening straps. It is recommended to replace all 4 at the same time. They keep the tub in the center of the cabinet and are sold individually.
The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably ...
This timer dial with compression ring shows you which part of the cycle your washer is in. It is white in color and can be found mounted on the timer shaft. You may need to replace this part if your ...
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you...
This part is the hub nut, or lock down nut for your washing machine. It is designed to hold the inner tub on to the transmission. If your hub nut is stripped or damaged, it may need to be replaced. T...
This drain hose is a replacement part for your top-loading washer. The hose measures 57 inches in length.
$74.14
Special Order
Questions And Answers for GBSR3140H2WW
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Todd
January 22, 2020
Clothes coming out of washer randomly soaked at end of wash, have used the cotton wash cycle on the timer exclusively for about 8 years. Found a tide pod smeared on clothes after one wash that was soaked. Dissasmbled pump but no issues with pump. Issues doesnt seem to be as bad on exra care cycle of timer. Agitation make some noise. Cotton cycle seems to miss part of high speed spin.
For model number GBSR3140H2WW
Hello, Thank you for your question. Here is what I found to look into: 1. Make sure the drain hose on the back of the washer is not clogged or bent. 2. Check that the drain hose on back of washer is positioned correctly in standpipe and is able to drain properly. 3. Check the drain pump debris filter or coin trap, objects may be blocking the water flow. 4. Check inside drain pump and all hoses connected to drain pump for foreign debris or small pieces of clothing. 5. Be sure the wash load of clothing is balanced, balance out the wash load if you see all clothing to one side. 6. Check washer belt to be sure it is not stretched out or damaged. (for most top loaders) 7. Check direct drive motor coupling system to be sure there is no visible damage. (for most front loaders) 8. Lid switch or door lock assembly may be damaged or bent and not making the electrical safety “connection”. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I spoke to a very nice young ladie who took my order and I received my order within two days. I pull the clasp off of the old knob and replace the knob and the clasp with the new part and it now works great. Thank you for helping me find the part I needed.
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor) 2. Removed the 2 bolts holding the Pump/Motor assembly to the machine. 3. Removed both hose clamps on the Pump/Motor assembly and removed Pump. 4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps. 5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump. 6. Plugged in the washing machine and everything worked.
NOTES: 1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine. 2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...
