This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
The rear drum support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. If your dryer is ...
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
This dryer lint screen is for laundry centers.
Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer.
Follow the instructions in the owner's manual when installing this part.
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so t...
$36.73
In Stock
Questions And Answers for FLEB8200DS0
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Julie
November 8, 2023
What is the size of the washer? Is it 3.9 cu ft? If not, is it bigger or smaller
Thank you
For model number FLEB8200DS0
Hello Julie, thank you for contacting us. According to our research, the capacity of the washer is 3.0 cubic feet. Glad to be of assistance!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Heidi
September 18, 2025
Water will only fill when left on the large load setting. What controls that and is it an easy fix?
For model number FLEB8200DS0
Hi Heidi, thank you for your inquiry. The water level switch or sensor, part number PS1146954, could be faulty. This sensor allows water to the washer after detecting the water level. If the sensor is faulty, water will not flow in properly. Glad to be of help!
Hello Alexander, Thank you for the question. In order to trouble shoot, we will need a bit more information. This is a Washer/Dryer combo, is it leaking from the dryer? More information on the location of the leak is needed. Please submit a new question if you have any follow ups. We are looking forward to hearing from you.
Was this helpful?
Thank you for voting!
Alexander
February 24, 2020
Leaking from the top, from the fill hose
For model number FLEB8200DS0
Hello Alexander, Thank you for contacting us. We suggest checking the Fill Hose Washer, PartSelect Number PS454170. If this does not fix the issue, the hose PartSelect Number PS468114 may need to be replaced. We hope this helps.
selected correct replacement knob. used small screw driver to remove small black metal sleeve from switch shaft. (had left that in place to be able to turn on dryer with needle nose pliers while waiting on knob). aligned flat of new knob with switch shaft and gently pressed into place.
Googled dryer start knob, Part Select was second site I clicked on, found within 1 min, part was inexpensive, easy to order, arrived quickly and fit perfectly. Excellent online ordering experience.
1. Unplug dryer from outlet 2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs 3. Lift up top and tilt back out of your way 4. Unscrew two phillips scews on inside of front panel 5. Lift up and out the front panel. Two spring clips at bottom. 6. Rlease tension on drum belt at the motor. Access panel at rear of dryer. 7.Unscrew 3 screws from inside, center rear of drum. 8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit 9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket) 10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer. 11. Vacuum everything--duct, blower, lint trap, ect. 12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside 13. reassemble remainder of parts in reverse order.
