This door shelf bin for your refrigerator snaps right into place on mounting tabs, requiring no tools for installation. The shelf is sold individually.
$68.12
In Stock
Order within the next 12 hrs and your part ships today!
This replacement drawer slide rail is for the right-hand side of your refrigerator. This part attaches to the inside wall of your refrigerator to support the sliding crisper drawer. If the rail is bro...
$69.57
In Stock
Order within the next 12 hrs and your part ships today!
This 40-watt appliance light bulb is a reliable replacement for use in select ranges, refrigerators, freezers, and microwaves. It provides bright, consistent lighting to help you see clearly inside yo...
$30.38
In Stock
Order within the next 12 hrs and your part ships today!
This defrost thermostat is a critical component in the refrigerator’s defrost system, designed to prevent overheating during the defrost cycle by regulating the temperature around the evaporator coils...
$32.93
In Stock
Order within the next 12 hrs and your part ships today!
This screw is used in refrigerators. The screw can be loosened or tightened with a Phillips-head or square-head screwdriver. This screw is used to secure the refrigerator handle to the refrigerator do...
$20.34
In Stock
Order within the next 12 hrs and your part ships today!
Tired of your fridge not staying as cold as it should be? It might be time to consider replacing your gasket-door ref. 21 in white from Frigidaire. This authentic part acts like a superhero, fighting ...
$206.41
In Stock
Order within the next 12 hrs and your part ships today!
This is the replacement meat pan for your refrigerator. It is made of clear plastic and is approximately 18 inches long and 13 inches wide. The meat pan slides into the bottom of the refrigerator shel...
$188.62
In Stock
Order within the next 12 hrs and your part ships today!
Keep your produce fresh and your refrigerator organized with this crisper pan cover, which includes the frame and insert. Positioned above the crisper drawer, it helps regulate humidity to prevent pre...
The run capacitor is attached to the compressor. This part is 120 volts and 15 mfd. The run capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things froze...
$48.68
In Stock
Order within the next 12 hrs and your part ships today!
This 8-cube ice maker is used to create ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen t...
$224.14
In Stock
Order within the next 12 hrs and your part ships today!
No instructions included, so it took a little bit of staring at the new part to figure out how it works. The barbed ridge on the gasket fits into a slot on the door. The flat face of the gasket has an internal magnetic strip that helps keep the seal tight against the steel face of the refrigerator. Installation requires no tools. This is the basic process: 1) Unbox the new gasket and get it ready to install so you don't have to leave the fridge open too long. 2) Open the door and grab the old gasket at one of the corners and pull away. This will unseat the barbed ridge I mentioned above. Work your way around the door until the whole gasket is free. 3) Set aside the old gasket 4) Grab a moistened paper towel and wipe down the (now exposed) sealing surface of the fridge and door. 5) Align the new gasket in the door and start pushing the barb into place. I found that the new gasket seemed slightly oversize compared to the original, so it took a little tweaking. What worked for me was to get all the corners seated, then work my way around the door making sure the gasket is fully seated. 6) Once you have the new gasket installed, close the door to make sure everything fits OK. 7) Open the door again and run your finger along the inside edge of the gasket seal. What you want to do is fold the edge of the gasket down so it lays flat against the outer wall of the door. 8) Shut the door and look from the sides and top to try to spot any gaps. You should be able to poke the gasket from the side and get the magnet strips to click into place. It seems like after a day or so the gasket 'relaxed' and I didn't have to worry about this anymore. 9) Dispose of the old gasket. I was able to pull the gasket into four pieces (separating at the corners) so it would fit in my city trash can...
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.
This was the second part I tried. The defrost timer was first, but that did not fix it. To do this I had to remove the ice maker and the back plate of the freezer. Then I defrosted the coil and cut the wires. stripped them back and installed the new thermostat. re-assembled and tested. has been working great ever since.
