The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broke...
$51.96
In Stock
Order within the next 1 mins and your part ships today!
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
$35.22
In Stock
Order within the next 1 mins and your part ships today!
The upper spray arm helps distribute water from the top of the dishwasher tub.This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwas...
$45.82
In Stock
Order within the next 1 mins and your part ships today!
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
$13.89
In Stock
Order within the next 1 mins and your part ships today!
This part is a replacement spray arm support for your dishwasher. It is made of white plastic and is approximately 3 inches long, 1 inch wide, and 3 inches tall. This is the support for the lower spra...
$15.17
In Stock
Order within the next 1 mins and your part ships today!
If your dishwasher won’t start or the door won’t close properly, the latch assembly might need replacing. This part helps keep the door securely shut and includes a switch that stops the dishwasher fr...
$60.21
In Stock
Order within the next 1 mins and your part ships today!
The upper dishrack is used to hold your dishes in place while the dishwasher goes through the wash cycles. Over time the dishrack can become damaged, start to rust, or be missing rollers, and the dish...
$148.07
In Stock
Order within the next 1 mins and your part ships today!
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
$35.80
In Stock
Order within the next 1 mins and your part ships today!
Order within the next 1 mins and your part ships today!
Questions And Answers for FFID2423RS3B
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mary
March 30, 2025
What is the height /width / depth measurement of this machine?
We need to buy a replacement (& have been happy with it for the last 10 years!), heating element is in need of replacement, and considering part cost & labor, we thought we'd buy new....Noticed many F'daire DW's are listed as "tall, at 35").....we don not have the space between the top of the door & counter to accommodate a 35" machine.....
TY
For model number FFID2423RS3B
Hello Mary, Thank you for contacting us. Researching this model, we show it is approximately 24 inches wide by 25 inches deep by 33 1/2 inches high. We hope this helps you.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Sahara
February 13, 2020
How to clean the filter
Cómo limpiar el filtro
For model number FFID2423RS3B
Good Day Sahara. Thank you for your question in regards to your unit (Model Number FFID2423RS3B). Based on our research, we found the following steps to help you clean out the filter on your unit. ***Ensure that before you begin you have unplugged the unit from the power source to avoid electrical shocks*** 1) Open your dishwasher door and pull out your bottom rack. 2) Remove the lower spray arm. 3) Lift up the tab that is securing the Drain Trap to the Base Filter and pull out the Drain Trap. 4) Turn the Support to the right and pull it out. 5) You will then be able to lift out the filter from your unit and take it to your sink to wash it and clean out the debris. We hope this helps! Best Regards.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the thing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..
