The Oven Bake Element is a black, metal part which supplies heat to the oven. This element is 19-1/2" wide x 18-1/2" long and has 3-1/2" inserts. It is rated as "Easy" to install by users, and attache...
This surface burner switch controls the stove top 8-inch surface burner temperature. This switch is 240-volt, 2100-2600 watt, and 8.8-10.8 amp. If your element is not defective but will not heat, you ...
The temperature sensor, also known as an oven probe, detects the temperature within the oven cavity. This temperature sensor is 9 inches in length and is a genuine OEM part. If your oven is too hot, n...
This handle mounting screw works with your oven or range, and bolts the door handle to the door. It is approximately 2 inches in length and is an OEM part sourced directly from the manufacturer. If yo...
This 40-watt appliance light bulb is a reliable replacement for use in select ranges, refrigerators, freezers, and microwaves. It provides bright, consistent lighting to help you see clearly inside yo...
The coil burner element is eight inches in diameter. It has four turns, 220 volts and looped terminal ends. The coil burner element provides heat to the cooking surface on your range. You might need t...
This is used as the "floor" of the oven cabinet.
Note: Does not come with rivets or screws. Must be purchased locally.
$134.48
In Stock
Questions And Answers for FFEF3015LSM
Ask our experts a question about this model and we'll get back to you as soon as possible!
11 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeff
January 16, 2020
Front left burner turns red hot while cooking you have to shut burner off to get it to cool of so you can cook have changed element did not fix
For model number FFEF3015LSM
Good Day Jeff. Thank you for your question in regards to your unit (Model Number FFEF3015LSM). Based on our research, you may need to replace the Infinite Burner Switch (PartSelect Number PS1145040) on your model. You can order this part either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.
11 people found this helpful.
Was this helpful?
Thank you for voting!
Randy
December 14, 2024
The burner light stays on after turning off, but burner is off! "No heat"
For model number FFEF3015LSM
Hello Randy, thank you for your question. The part needed is the Light Indicator PS436960. Good luck with your repair.
I am looking for two 8 inch black drip bowls. Is this a different size as most other Generic brands do not fit correctly. They are too big. The inner metal is 7-3/4 inches.Thank you, Bob
For model number FFEF3015LSM
Hi Bob,
Thank you for your question. The part number listed under your model number for the black 8 inch drip bowl is PS1537685. We hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Cynthia
September 2, 2025
I need the bracket that holds the drawer in place. It attaches to the side wall of the bottom panel of the stove. It might be part 41 or 41A.
For model number FFEF3015LSM
Hello Cynthia, thank you for getting in touch. The part you are looking for is the drawer glide, part number PS12584887. We hope this helps.
1. Removed two screws, pulled out the element, voltage tested the element and determined it was an open circuit (bad element). 2. Ordered the part from partselect.com 3. Disconnected element, connected the new one, and screwed it back in.
Shut off circuit breaker to stove and collected the tool from the basement. Turned on flashlight. Unscrewed the two hex nuts from the old element/back of the oven. Slid the old element prongs out of the back, exposing the connecting wires. Pulled the connecting wires off of the old element, carefully, so that the connections wouldn't come off of the wires. Threw the old element pieces in the garbage. Connected the new element to the connecting wires and re-fastened the hex nuts. My husband had wanted to call the repair man, but it didn't look too difficult, so I decided to try it on my own. Boy was he surprised when I fixed it, and for a fraction of the cost of hiring a repairman! Ladies, we can do this ourselves!!! :) Thank you for being there for us to order our part from, Parts Select, we had our new part in less than 24 hours, so the shipping was blazing fast!!! Keep up the good work!!! :)
