The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broke...
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
The upper spray arm helps distribute water from the top of the dishwasher tub.This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwas...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
This part is a genuine OEM part. This grey lower dish rack assembly comes with eight light-gray rollers for easy access. The dish rack is approximately 21 inches wide x 22 inches deep. The dish rack h...
This part is a replacement spray arm support for your dishwasher. It is made of white plastic and is approximately 3 inches long, 1 inch wide, and 3 inches tall. This is the support for the lower spra...
The upper dishrack is used to hold your dishes in place while the dishwasher goes through the wash cycles. Over time the dishrack can become damaged, start to rust, or be missing rollers, and the dish...
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
The drain hose connects to the pump located below the lower spray arm. It aids in proper dishwasher drainage. Size: 7.5 feet long
$49.42
In Stock
Questions And Answers for FFBD2408NS8C
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Marsha
November 29, 2019
I need the part label number 11 from the diagram motor and pump.
For model number FFBD2408NS8C
Hi Marsha, please call us at 1-877-910-4613. Thank you for your question and good luck with your repair!
How do you clean inside this machine-the filter etc
For model number FFBD2408NS8C
Hi Margaret,
Thank you for your question. To clean the filter, you will need to clean it in a solution of dish soap and water. You will need to use a cloth to wipe it and you should have an old toothbrush on hand to scrub any difficult areas. If this method does not help to get the filter clean, it will need to be replaced. To clean the inside of the dishwasher, you may purchase some dishwasher cleaning tabs, such as Affresh, at your grocery store or you can use vinegar and hot water to clean it. Place some vinegar in a dishwasher safe container and place it on the top rack. Then run the dishwasher on the hot water cycle. This will remove any grime, dirt or soap residue from your dishwasher. We hope this helps. Thank you and have a great day.
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the thing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..
