Also known as Probe. The quick connect on this part may be different than your original part. If it doesn't fit, you have to cut off the quick connect and wire together with porcelain wire nuts.
This 40-watt appliance light bulb is a reliable replacement for use in select ranges, refrigerators, freezers, and microwaves. It provides bright, consistent lighting to help you see clearly inside yo...
This broil element is found on the roof of the oven and heats food. The most common reasons you would need to replace this part is due to the oven not giving off enough heat, not turning on, or not ba...
The 6” radiant cooking element with limiter fits under the glass cooktop and supplies heat to the cooking area. If your element is not heating, you can test the element for continuity with a multimete...
This retainer secures the light lens to the oven cavity.
No Longer Available
Questions And Answers for FES388WGCC
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
March 24, 2020
How can i unlock the oven door ??
For model number FES388WGCC
Hi John,
Thank you for your question. If the door will not unlock at the end of the clean cycle then you may have a problem the door lock/motor assembly. You should first remove the power to the oven for a few moments and then reconnect. This may reset the control and allow you to unlock the door. If you suspect that the door lock/motor assembly is at fault, then you will need to unlock the door manually. The assembly is normally located between the main top and the oven and can only be accessed by raising the main top. This is very difficult to do because the screws that hold the top in place are inaccessible with the door closed. If the assembly cannot be accessed then you will have to form a wire hook,(coat hanger) and insert it between the door and the latch and manually pull the latch to the open position. Remove power to the oven before attempting this procedure and be careful not to damage the finish. If the switch is not working, you will need to test it with a multi-meter. Unplug your oven before beginning this test. Depending on your model, the switch could be found in several places, refer to your owner’s manual to determine the exact location. Common locations include the control panel & the door frame. Once you have located it, remove it in order to test for continuity.
Set your multi-meter to Rx1 and ensure the switch is turned to the “clean" position. Using the probes, touch the terminals of the switch, this should produce a reading of zero or nearly zero. If your test results show that there is no continuity, you will need a replacement door lock switch. We hope this helps. Thank you and have a great day.
The repair was simple; first I removed the 2 screws from the old element and disconnected the wires and then I inserted the new element reconnected the wires and replaced the screws . The repair was easy and took less that 15 min. The oven works as good as new and I saved alot of money by doing it myself.
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
