This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating. This part is located in the blower housing.
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
INCLUDES 5304523151 SHAFT, 5304523152 ROLLER, 5304523153 NUT, 5304523154 SPACER.
$93.76
In Stock
Questions And Answers for FAQE7011LW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Benjamin
November 9, 2022
the digital lights are flashing and the dryer doesn't start
For model number FAQE7011LW0
Hello Benjamin, thank you for reaching out. We recommend that you check the door switch, part number PS2330880, the thermal fuse, part number PS4704883, and the thermostat, part number PS446428, for any damage and replace the defective part, so your dryer starts working. Please reach out to customer service if you need help placing an order. Glad to be of help!
Why is dryer NOT getting hot? Every thing else is working
For model number FAQE7011LW0
Hello Herbert, thank you for reaching out. We would recommend taking a look at the thermal fuse to see if it is working or not. The fuse should be closed for continuity, meaning it has a continuous electrical path through it when it is good. If overheated, the fuse will have no continuity, meaning the electrical path is broken and the fuse has blown. You will need to replace the thermal fuse, part number PS2349395. Inspect the high-limit thermostat and control thermistor. The high-limit thermostat monitors the dryer temperature and shuts off the burner if the dryer overheats. If the high-limit thermostat is malfunctioning, it may shut off the burner even if the dryer is not overheating. Test the thermostat by using a multimeter to check for continuity. If the thermostat does not have continuity, replace the high-limit thermostat, part number PS446428. A dryer thermistor monitors the temperature of the burner or heater housing and will shut off the heat once a sufficient temperature is reached. If the thermistor is faulty, the dryer may not heat at all. You need to replace the control thermistor, part number PS1149368. If these do not solve the issue, we suggest replacing the heating element, part number PS2367792. We hope this helps, good luck with this repair!
Hi Richard, thank you for the question. Based on our research, there are two high limit thermostats listed for your model, one on the heater assembly and the other on the air duct in the back. We hope this information helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)
