This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately f...
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
This washer shock absorber mounting pin is a small but essential fastener that secures the shock absorber to the outer tub of a front-load washing machine. By holding the shock absorber firmly in plac...
Your washer's door glass panel is the window to efficiency and cleanliness. If it's compromised, it may affect your appliance's performance. That's where our genuine Frigidaire Door Glass Panel comes ...
This washer tub-to-pump hose, often called a coin trap or bellows hose, carries water from the outer tub to the drain pump during drain and spin cycles. Designed with an integrated trap, it captures c...
When you're dealing with an ineffective washing machine, our Frigidaire Boot Seal Retaining Ring can be the solution you need. This is more than just a replacement part- it's about making your machine...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kirby
December 12, 2022
E32 preasure sensor switch.
Washer shows "sensing" and does nothing.
For model number FAFS4073NW0
Hi Kirby, thank you for reaching out. The E32 means the water level pressure switch is not communicating with the electronic control board. Unplug the washer and check the wire harness connections between the water level pressure switch and the control board. If the wiring connections are good, then you will need to replace the water level pressure switch, part number PS2349296. If you require assistance placing an order, please contact customer service. We hope that helps!
When I try to start the washer I get a "sensing" message and then "door open" even though the door is closed. DO I have a bad door sensor ? The prong on the door is fine and enters the sensing hole.
For model number FAFS4073NW0
Hello Mitchell, thank you for your inquiry. The problem seems to be with the Door Lock and Switch Assembly and you may need to replace it, the part number is PS12364048. If that does not help, we would suggest checking the Door Striker, part number PS2378364. If you require assistance placing an order, please contact customer service. We hope that helps!
Hola Gabino, Gracias por contactarnos. No realizamos envíos fuera de los EE. UU. Continentales, pero si conoce a alguien en los EE. UU. Continentales a quien podamos enviarle la pieza, puede hacer arreglos con esa persona para que le envíe la pieza. ¡Esperamos que esto te ayude!
Was this helpful?
Thank you for voting!
Traci
January 27, 2025
Need a full door assembly
For model number FAFS4073NW0
Hello Traci, thank you for contacting us. The door for your model does not come as an assembly and its parts are sold separately. We have attached a relevant link that will help you in ordering all the door parts. You can find the door parts on the top left of the diagram in this link. Glad to be of help!
Hello Chris, thank you for reaching out. The E53 error code means there is a communication failure between the motor control board and the main control board. This usually happens when the main control unit isn’t receiving proper signals from the motor control board, which controls the washer’s motor speed and operation. The most common causes include a loose or damaged wiring harness between the boards, a faulty motor control board, or in some cases, a defective main control board. To fix the issue, unplug the washer and check all wiring connections to ensure they are secure and free of damage or corrosion. If the wiring looks fine, the motor control board is likely the problem and should be replaced. If replacing the board does not solve the issue, the main control board may also need to be replaced. The motor control board is part number PS10066118, and the main control board is part number PS10063112. We hope this solves your problem!
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse.
