F1201FD LG Washer - Instructions

Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.

I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.

There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replace the magnet was $18. Instructions were included in the box. Part number on the drawing was A165. PS3618292 Magnetic Door Plunger

Watched a short video to figure out to remove panels. After panels were off I removed as much as I could from the inside of the machine. This was not completely necessary however for an extra half hour it made inspection, cleanup and removal of tub housing out the front of the machine much easier. Once out, I split the two halves of the outer basin and sprayed the spider shaft with penetrating oil. Using a brass drift I did have to get a bit aggressive to drive spider shaft out, then I used a heavy metal punch to hammer out the bearings. For those who may not know using brass or a soft metal will keep from damaging reusable parts. At this point it was cleanup time, with dish soap I scrubbed the two halves of the outer basin and the wash basin itself then used emery cloth on the bearing casing and spider shaft. I am a firm believer if u take the time to cleanup properly things go back together much easier. At this point I began to reassemble, replacing tub bearings and seal, the wash basin then putting the two halves of the outer basin back together. I strongly recommend replacing gasket for the halves of the outer basin, for as much as it takes to get there it is money well spent to up the chances of a leak free system. Now with the wash tub back together it was time to reset the tub and hook everything back up. I skipped a lot of steps but if a person pays attention, takes pictures if they have to, even numbers lines with a sharpie it is a very easy repair. Very easy but very time consuming. I am DIY’er, in all I spent about ten hours over two days to do this job. Thus being said I am very particular spent a lot of time cleaning, scrubbing looking at as many wear points and checking for rubbed wires. Hope this helps someone out there, definitely not a strong writer or like doing it. Oh one other thing, I ordered the shocks on the bottom side of wash tub just because I guess not thinking they were bad just thinking I could help tune it up. Was surprised to find the old ones were completely shot, was glad I ordered new ones. After repairs, noise is gone and machine is quiet again. Thank you, your website is very easy to find parts and order.

Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.

Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.

replaced the cold water valve inlet

Watched a you tube video and followed the instructions. Even had my 11 and 13 yo old help and do most of the work. Very easy to fix both hot and cold inlet at the same time. Didn't know which one was causing the problem so I decided to replace both.

Followed directions on the video and went like a charm. Very impressed with service and video

Removed back of washer with screw driver, Removed outer motor cover with a 17 mm socket (1 bolt), Removed motor stater using 10 mm socket (8 bolts). Left motor plugged in and and tipped to the side exposing the sensor. Unplug and snap off sensor. Reassembled in opposite order. Machine works great. Very easy fix, and perfect fit on part.

I received the locking device. I received an email from parts select with a repair video link. I watch the video and repeated the steps. Very easy and educational. Thank you for simplifying something I have limited experience doing.

Removed and replaced. BUT...

BUY THE TOOL! Buy the spring expander tool. I tried with needle nose and bloodied my knuckles. I am sure you all are strong and more adept, but next time I will buy the tool.

I first thought there was a mechanical problem but after checking everything mechanical I discounted that idea ... I researched and found out from others with a similar problem that the Le code display was probably a sensor problem ... I ordered a replacement sensor ... With the new sensor available, I removed the access panel to the back of the machine (phillips head screw driver - 4 screws) ... Remove the exposed motor half (1 bolt - 17mm scocket) ... Loosen the motor stator that has the wired coils (10mm socket - 6 bolts) ... Hold motor unit to the side without disconnecting the wiring harness ... Disconnect the sensor wire connector and remove the old sensor ... Clip the new sensor in place (same position as the old one) and re-connect ... Reverse the assembly procedures ... This fixed the problem and the washing machine works like a new one ... The wife is HAPPY!

There are two pumps in this system. I turned the washer on its side and took off bottom plate. There are several screws holding this on. I then took the entire pump assembly off. There are 3 screws holding each pump on the brown plastic body. Each pump has a positive and negative lead. I switched out the pump and reassembled. The hardest part is getting the 3 "shock absorbers in place with the rubber sleeves. I think the book suggest getting to the pump from the front side but I went through the bottom. Worked good. I did wonder however if the other pump was working. Do you need two pump working to get flow? By replacing one pump I went from no flow to good flow. Cost me $75.00

I did repaired while looking at video at your site .thanks to your team ..