This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$27.85
In Stock
Order within the next 8 hrs and your part ships today!
This washer shock absorber mounting pin is a small but essential fastener that secures the shock absorber to the outer tub of a front-load washing machine. By holding the shock absorber firmly in plac...
$29.73
In Stock
Order within the next 8 hrs and your part ships today!
This front-load washing machine door boot seal is a flexible rubber component designed to create a watertight barrier between the washer’s door and the inner tub. It plays a critical role in preventin...
$189.61
In Stock
Order within the next 8 hrs and your part ships today!
The door strike attaches to the door of your front load washer and will activate the door switch once the door is closed. If your washer won’t start or the door won’t close/open properly, you may need...
This washer tub-to-pump hose, often called a coin trap or bellows hose, carries water from the outer tub to the drain pump during drain and spin cycles. Designed with an integrated trap, it captures c...
$120.61
In Stock
Order within the next 8 hrs and your part ships today!
Have you been facing leaking issues with your washing machine? Our genuine and high-quality Frigidaire Bellows Spring Clamp could be the simple solution you need. Designed for your washing machine's d...
$44.35
In Stock
Order within the next 8 hrs and your part ships today!
Reduce vibrations and noise during wash and spin cycles with this shock absorber kit, designed to stabilize the washer tub for smooth, quiet operation. Made from durable plastic and rubber components,...
$98.81
In Stock
Order within the next 8 hrs and your part ships today!
This spring helps keep the rubber seal around your washer’s door in place, stopping leaks and keeping everything running smoothly. If your washer is leaking or the seal looks loose, this part might be...
$64.00
In Stock
Order within the next 8 hrs and your part ships today!
Questions And Answers for EWFLW65HIW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bill
November 29, 2022
What part number/model drain pump do I need for this washing machine?
For model number EWFLW65HIW0
Hello Bill, thank you for reaching out. The part number for the drain pump compatible with your given model is PS2342436. If you require assistance to place an order, please contact customer service. We hope that helps!
The lights around the selector knob will sometimes randomly come on and go round and yesturday during a wash cycle the blue lights randomly went around the selector knob by them self
For model number EWFLW65HIW0
Hi Kurt, thank you for getting in touch. We would recommend checking the washer control board, part number PS2349340. You may need to replace it to fix the issue. We hope that helps!
Removed old drawer and replaced it with new one. This is the second drawer assembly I have purchased in 6 months. This piece of junk must be a cash cow for Electrolux. If they would make the small latch out of metal instead of plastic, there would be no problem. But that might cost an additional $ .007 per washer. On the positive side, partselect.com had the part and delivered it promptly.
Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfectly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.
First, I went to the PartSelect website and easily found the part at a reasonable price. I ordered it early on a Wednesday afternoon, and gladly spent the extra $25 to ship it overnight. That evening, PartSelect sent me an email stating that the part had shipped that very day, and - mistakenly - I took that literally. FedEx tracking predicted that the part would arrive on Friday, July 5, which made sense because the 4th was a holiday. But I found out that the part had actually shipped on the 3rd, as the email had informed me. It didn't actually ship until the 4th - up until then, a "shipping label" had been created but it had not shipped. FedEx then revised their arrival date to Monday, 8 July. That clearly wasn't satisfactory. So I went to my local parts distributor, Dayton Appliance Parts, a fifteen-minute drive from my house, and got the same part for $3 cheaper, plus without the $25 shipping fee that PartSelect had charged me for overnight-shipping-that-isn't-actually-overnight-shipping. Once I had the part in hand, installation was a breeze. Two screws removed, pulled the striker, replaced the new part and the screws. Less than two minutes. But no thanks to PartSelect.
