This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
This front-load washing machine door boot seal is a flexible rubber component designed to create a watertight barrier between the washer’s door and the inner tub. It plays a critical role in preventin...
The door strike attaches to the door of your front load washer and will activate the door switch once the door is closed. If your washer won’t start or the door won’t close/open properly, you may need...
Ensure proper drainage and protect your washer from damage with this durable tub-to-pump hose, designed for front-load washing machines. This genuine replacement part carries water from the tub to the...
Have you been facing leaking issues with your washing machine? Our genuine and high-quality Frigidaire Bellows Spring Clamp could be the simple solution you need. Designed for your washing machine's d...
Reduce vibrations and noise during wash and spin cycles with this shock absorber kit, designed to stabilize the washer tub for smooth, quiet operation. Made from durable plastic and rubber components,...
This genuine OEM drain pump is an essential component for removing water from the washer tub during the drain cycle. Built from durable materials, including impact-resistant plastic and stainless stee...
$220.59
In Stock
Questions And Answers for EWFLS70JIW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Eileen
October 22, 2021
I used the tide washing machine cleaner and now i have a lingering odour on my clothes. I did follow the instructions to to followup up the cleaning with the spin & rinse on my washer. What can i do to get rid of the odour? Thank you.
For model number EWFLS70JIW0
Hi Eileen,
Thank you for your question. If your clothes have a lingering odor after using the tide washing machine cleaner, pour 2 cups of vinegar into your detergent drawer and run the washer empty on the hot water cycle on the longest setting. This should remove the lingering smell. We hope this helps! If you have any questions, please let us know.
Was this helpful?
Thank you for voting!
Corrina
November 28, 2025
Why does the fabric softener compartment not empty?
For model number EWFLS70JIW0
Hi Corrina, thank you for reaching out. A softener compartment that does not empty is most often caused by a hardened fabric softener or general residue that can block the siphon tube. Remove the dispenser drawer and clean all components thoroughly with warm water and a soft brush. If that is not the issue, the water inlet valve, part number PS2349248, might be faulty and needs to be replaced. We hope this solves your problem!
Removed old drawer and replaced it with new one. This is the second drawer assembly I have purchased in 6 months. This piece of junk must be a cash cow for Electrolux. If they would make the small latch out of metal instead of plastic, there would be no problem. But that might cost an additional $ .007 per washer. On the positive side, partselect.com had the part and delivered it promptly.
Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfectly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.
First, I went to the PartSelect website and easily found the part at a reasonable price. I ordered it early on a Wednesday afternoon, and gladly spent the extra $25 to ship it overnight. That evening, PartSelect sent me an email stating that the part had shipped that very day, and - mistakenly - I took that literally. FedEx tracking predicted that the part would arrive on Friday, July 5, which made sense because the 4th was a holiday. But I found out that the part had actually shipped on the 3rd, as the email had informed me. It didn't actually ship until the 4th - up until then, a "shipping label" had been created but it had not shipped. FedEx then revised their arrival date to Monday, 8 July. That clearly wasn't satisfactory. So I went to my local parts distributor, Dayton Appliance Parts, a fifteen-minute drive from my house, and got the same part for $3 cheaper, plus without the $25 shipping fee that PartSelect had charged me for overnight-shipping-that-isn't-actually-overnight-shipping. Once I had the part in hand, installation was a breeze. Two screws removed, pulled the striker, replaced the new part and the screws. Less than two minutes. But no thanks to PartSelect.
