This manufacturer-approved air filter system for refrigerators eliminates odors and any impurities. It does this by neutralizing and removing odor-causing molecules. For best results, it is important ...
$45.61
In Stock
Order within the next 12 hrs and your part ships today!
This GREY magnetic door gasket is designed to help your 36-inch French-door refrigerator maintain a consistent internal temperature by forming a tight seal between the doors and the cabinet. Made from...
$112.61
In Stock
Order within the next 12 hrs and your part ships today!
This is a genuine Frigidaire part for your refrigerator. This is an ice maker, which connects to the water lines to provide fresh ice. The most common reason to replace this part is if your refrigerat...
$154.43
In Stock
Order within the next 12 hrs and your part ships today!
This water filter reduces contaminants to improve water clarity, taste, and overall quality. Clean water supports appliance performance and user satisfaction. Regular replacement helps maintain optima...
$109.42
In Stock
Order within the next 12 hrs and your part ships today!
This screw is used in refrigerators. The screw can be loosened or tightened with a Phillips-head or square-head screwdriver. This screw is used to secure the refrigerator handle to the refrigerator do...
$20.34
In Stock
Order within the next 12 hrs and your part ships today!
Ensure your freezer operates efficiently with this replacement drawer gasket, designed to form a tight seal that keeps cold air in and warm air out. Made in light gray and compatible with select model...
$97.13
In Stock
Order within the next 12 hrs and your part ships today!
This mullion hinge pin is designed to secure the mullion in place within compatible refrigerator models, allowing it to pivot smoothly as the doors open and close. Measuring approximately 1.5 inches b...
$32.93
In Stock
Order within the next 12 hrs and your part ships today!
This small but important part helps your fridge defrost safely. It keeps an eye on the temperature of the coils and shuts off the heater when things get warm enough. That way, your fridge doesn’t over...
$90.11
In Stock
Order within the next 12 hrs and your part ships today!
The water inlet valve supplies water to the refrigerator ice maker and water dispenser.
This part works with the following brands: Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Sears...
$252.37
In Stock
Order within the next 12 hrs and your part ships today!
This genuine OEM evaporator fan motor is essential for maintaining consistent cooling inside your refrigerator by circulating cold air over the evaporator coils and distributing it throughout the fres...
$149.71
In Stock
Order within the next 12 hrs and your part ships today!
First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There is 2 screws holding the solenoid in place and one ground wire. This was an easy fix and I know I saved a lot of money.
Simple three steps... 1) There's an front section to the ice-maker to take off. One Phillips screw is on the side, one screw is underneath near the inside of the refrigerator wall. Just unscrew and store. 2) There's a small plastic unit just inside the ice maker to take out. It's held in by a small nut that requires about a 4" extension to reach. (You may be able to unscrew the nut with small needle-nose pliers). Just unscrew and take out the unit - the unit functions just to keep the ice maker wiring in place. 3) The wiring looks a mess, but there's just one wiring connector to the ice maker assembly. Unsnap it. The ice maker is not screwed in, it just slides in -- reach in and pull the assembly straight out; when it stops, lower it a bit and it will come free. Reverse the instructions to install the new unit.
I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!
