This dishwasher drain and wash impeller kit comes with both the drain and wash impeller, gaskets, chopper and installation screw. This part helps stop your dishwasher from leaking and helps with the ...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of wat...
This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element.
The lid hinge pin or detergent lid pin on your dishwasher helps dispense your dish detergent when your dishwasher is running. The pin fits with the dispenser lid and allows the lid to pop open and dis...
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
May 29, 2023
We had a glass break during operation. How are are the pieces best removed?
For model number DU920PWKB0
Hi Mike, thank you for reaching out. You can follow the following steps to remove pieces:
1. Turn off the circuit breaker supplying power to the dishwasher at the main circuit breaker panel.
2. Open the dishwasher door and remove the upper and lower dish racks from the appliance.
3. Remove the broken glass from the drain basket and surrounding area using a wet or dry vacuum. Larger pieces that the vacuum cannot handle should be carefully removed by hand.
4. Loosen and remove the basket mounting screws by turning them counterclockwise with a nut driver or screwdriver.
5. Inspect the area beneath the drain basket for any remaining glass fragments using a flashlight. Use the wet vacuum to remove the pieces if necessary.
6. Re-install the drain basket by securing it with the mounting screws.
7. Replace the upper and lower dish racks and restore the power.
We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Steve
December 17, 2019
My spray tower was found in bottom of dishwasher and would like to know how to fix?
For model number DU920PWKB0
Hello Steve and thanks for writing.
You need to check if the arm PS11745481 itself did break off or if it just came loose, here is a link to the diagram to establish different parts for the arm.
https://www.partselect.com/Models/DU920PWKB0/Sections/DISHRACK/?ModelID=788924&ModelNum=DU920PWKB0&mfgModelNum=&ManufactureID=3&Selected=PHDCOQZW&Position=1&mfg=Whirlpool&Type=Dishwasher&Mark=1
Let us know once you established if the arm itself is broken or not if you need any further assistance with parts. We hope this helps. Please contact us anytime.
Installed new door seal. Dishwasher still leaked. Googled the model number and then cleaned the filter at the bottom of the dishwasher, still leaked. Verified that manifold bearing was not work. It was OK. Found note that a plugged vent might cause leaking door. Very counterintuitive. Pried off air vent cover. Vent was thouroughly plugged with calcium deposts from steam. Cleaned these out. Dishwasher no longer leaks.
Disconnect unit and remove from under counter. remove lower spray arm, tip over dishwasher on it's back, diconnect wires from motor , unscrew drain fitting rotate motor mounts to and lift pump and motor assembly up and out from inside the dishwasher. thoughly clean all parts during pump disassembly( under running water and a toothbrush works well) . Looking at a parts diagram,and using your memory from disassembly replace the new seals and put it all back together, with patience you can do anything and use common sense.
Ordered both drain & wash impeller kit and the drain check valve with o-ring. Decided to test the cheaper drain check valve first. Pulled dishwasher out from wall & adjacent cabinetry; removed drain hose from disposer and drained as much water as possible; "jacked" side of dishwasher to gain access to drain hose and drain check valve; used pliers to remove hose clamp; placed flat pan underneath to catch remaining water drainage; unscrewed drain check valve; tested under bathroom faucet--determined faulty; replaced with the new one, restored connections, reset dishwasher in proper location; voila--fixed! Plan to return the unneeded impeller kit.