This dishwasher door gasket creates a watertight seal between the door and the tub, preventing leaks during wash cycles. Made from flexible black rubber, it fits securely along the edge of the door to...
This part is a replacement tine row clip for your dishwasher. The tine row clip is adjustable, and it fits onto your dishrack to holds the tines into place. If your dishrack tine rows will not stay in...
This is a replacement water inlet valve for your washer. The water inlet valve in your washer connects to the water source and solenoid wires, and ensures the tub has the right amount of water enterin...
If your dishwasher isn’t draining or cleaning well, this drain pump could be the issue. It helps move water out of the tub during the cycle and fits many Bosch, Thermador, and Gaggenau models. Signs i...
If your dishwasher is leaking or not draining properly, this replacement drain hose might be the fix. It connects the dishwasher to your sink drain or garbage disposal, carrying away dirty water after...
Ensure proper detergent release during wash cycles with this genuine latch kit, designed to open the detergent cup at the right time and prevent premature opening. The kit includes a latch, spring, an...
This dishwasher door latch helps keep the door shut tight during cycles, preventing leaks and making sure everything runs smoothly. It also tells the dishwasher when the door is properly closed. Easy ...
Give your dishwasher a clean, polished look again with this replacement toe kick panel. It covers the bottom front of your appliance, protecting the internal parts from dust and moisture while hiding ...
$98.41
In Stock
Questions And Answers for DF251760
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Here are the steps you need to take to do the job properly:
1. turn off electrical circuit breaker to the dishwasher 2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed. 3. unplug the wiring harness to the detergent/rinse aid dispenser 4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser. 5. the unit will pop out toward the inside of the dishwasher 6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in. 7. re-attach the wiring harness 8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job. 9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks. 10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.
With the help of You Tube, this 50 year old Mom got the job done. Not that complicated if you watch the step by step instructions on the Appliance Pro video. My repairman and husband were both determined to just buy a new one but this 20 year old dishwashing genius was just in need of a little repair. Only need a screwdriver, and slightly confusing as wires hook on a little different on new pumps. I suggest watching video the whole way through and then playing it step by step as you do the repair. Worked great for me. Thanks.
I used a wet vac to remove the water from the dishwasher. remove cover and filter/strainer from bottom of dishwasher. remove screw which allows you to lift the plastic piece to access check valve. Original check valve looked like new , I installed new check valve re installed parts . Job done and issue resolved .
