This NSF-certified refrigerator water filter is engineered to improve the taste, clarity, and safety of your drinking water by reducing contaminants such as mercury, lead, and trace pharmaceuticals. D...
The interior light of your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, there could be an issue with the sw...
The Refrigerator Evaporator Fan Motor is an OEM replacement part for some GE refrigerators. It is responsible for circulating air over the evaporator coils, which are responsible for cooling the refri...
This LED light and cover assembly is designed for the fresh food compartment of compatible refrigerators, providing bright, energy-efficient illumination to help you easily see and access stored items...
If your fridge is building up too much frost or not cooling evenly, this defrost thermostat might be the issue. It helps control the temperature during the defrost cycle by shutting off the heater whe...
If your fridge is frosting up or not cooling like it should, this defrost heater might be the issue. It melts ice off the coils so your fridge can stay cool and run efficiently. It’s a genuine replace...
If your fridge isn’t staying cool or you’re hearing strange noises from the back, the condenser fan motor might be the problem. This part helps move air over the coils to keep things cool and running ...
Facing problems with your fridges defrost cycle? The GE HEATER DEF Assembly FZ could be the solution youve been looking for. This vital piece of kit helps your refrigerator maintain its optimum effici...
This freezer evaporator fan motor and felt assembly is essential for maintaining consistent cooling throughout your refrigerator’s freezer and fresh food compartments. It circulates cold air over the ...
$174.57
Special Order
Questions And Answers for CWE23SSHSS
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Deborah
March 28, 2026
One of the six covered LED lights is not working. The other five are dim. These are located at the outer edge of the main compartment. I pulled the unlit component away frome the wall of frig. It is a tiny component attached by wires to the inside of frig. What is the number of the appropriate replacement part? Is it easy to replace?
For model number CWE23SSHSS
Hello Deborah, thank you for reaching out. The LED lights in your refrigerator section are part number PS4704284. To replace the LED assembly, follow the following instructions: 1. Insert the flat-blade screwdriver and pry out the old LED cover. 2. Press down on the locking tab and disconnect the plug. 3. Take the new LED cover and push it in so that it will lock and connect to the plug. 4. Snap the cover into the housing. We hope this helps. Good luck with this repair!
I went to a GE repair center to explain my problem, the service center reccomended that I have a techinician come out o look at it. $75.00 for the visit and what ever labor and materials wuld cost.
I went on line to see if there were others having this same problem and found that there were many with the same problem.
After reading some of the ways that people found out what was wrong ...it became a matter of three components, the timer, heater or thermostat.
I tried the most common component and the less expensive one first , the thermostat switch I installed it very easily snipping two wires and attaching the news using wire nuts I used the diagram on this website to pinpoint the component and there has not been a problem since.
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the catch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.
