CVM721M2N8S5 General Electric Microwave - Overview
Sections of the CVM721M2N8S5
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
HALOGEN LAMP
PartSelect #: PS16216934
Manufacturer #: WB02X35488
You can always rely on our GE Halogen Lamp to keep your appliance shining bright. This high-performance halogen lamp was made by GE, specifically for your appliance. Wondering why its such a critical ...
No Longer Available
Primary Door Interlock Switch
PartSelect #: PS237015
Manufacturer #: WB24X10047
This interlock switch is located in the door latch.
$54.49
Special Order
Monitor Interlock Switch
PartSelect #: PS11766871
Manufacturer #: WB24X25397
If your microwave won’t start even though the door is shut, this switch might be the reason. It helps your microwave know the door is closed so it can run safely. This genuine part is easy to install ...
No Longer Available
Cable Assembly
PartSelect #: PS16219547
Manufacturer #: WB27X35382
This part is the replacement high-voltage diode for your microwave. It is approximately 3 inches long and is sold individually. The high voltage diode is an electrical current control device inside yo...
No Longer Available
Microwave Exhaust Adapter
PartSelect #: PS12709817
Manufacturer #: WB02X32715
This is the replacement damper bracket for your microwave. It is made of plastic and is approximately 11 inches wide and 3 inches long. The damper bracket attaches to the outer cabinet and directs air...
No Longer Available
Capacitor
PartSelect #: PS2353613
Manufacturer #: WB27X11033
This capacitor delivers the electrical boost required for motors to start and operate efficiently. Proper capacitance reduces strain on motor components and helps prevent startup failures or inconsist...
$72.93
Special Order
Microwave Humidity Sensor
PartSelect #: PS1020486
Manufacturer #: WB27X10857
The humidity sensor detects humidity inside the microwave and communicates the temperature to the electronic control board.
$142.13
Special Order
Mounting Plate Assembly
PartSelect #: PS16216996
Manufacturer #: WB56X35363
This mounting plate, also known as a bracket, is crucial for keeping your microwave mounted to the wall, when placed above the stove. This OEM part is sold separately from the screws that are needed t...
No Longer Available
Questions And Answers for CVM721M2N8S5
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
M
January 20, 2024
All sounds have stopped or only partially come out, regardless of volume setting. Is there a speaker replacement?
For model number CVM721M2N8S5
Hi M, thank you for reaching out. Based on our understanding, the issue is most probably with the user interface board. The user interface board for your model is not sold separately, it comes with the door assembly. You may need to order the door assembly for it, the part number is PS16219630. We hope this helps.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the CVM721M2N8S5
[Viewing 4 of 4]No heat
Fixed by
these parts
these parts
Show All
Won’t turn on
Fixed by
these parts
these parts
Show All
Doesn’t shut off
Fixed by
these parts
these parts
Show All
Tray won’t turn
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave would turn on and count down, but not heating and not rotate turntable. Pressing door up would occasionally start heat.
First I disconnected the power and opened the door. Then I removed the top screws holding the top vent louvers, then removed the screw at the top of the touch pad. The touch pad removes by sliding up slightly then tilting top out. I unscrewed two screws holding the door latch assembly. Press the tab to remove and replace switch. Reconnect wires, reseat latch mount by placing top bracket tab in place first, allign and secure with screws. Reseat touch pad by placing bottom tabs in first, tilt forward and press up to seat top tabs, secure with top screw. Secure vent louver screws, plug in and watch your microwave work again.
Parts Used:
-
Michael from Ridgefield, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
40 of 67 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave runs with the door open
Remove microwave outer cover. Turn on side & locate the upper & lower door switches. Better to replace in pairs even if one is ok. Remove the wire harness to each switch. Then replace switch and re connect the wire harness. Re attach outer cover
and test to see if that solved the problem. If so then well done!!
and test to see if that solved the problem. If so then well done!!
Parts Used:
-
Thomas from Andover, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
37 of 58 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave made loud buzz noise and did not heat
I followed the generic trouble shooting directions on the web site. It suggested either diode, capacitor and/or magnetron. I test each. All tested OK except diode. It was supposed to measure open in one direction and appox 200k ohms in the other direction. My diode measured open in both directions (tried multiple times, multiple settings). I replaced the diode. The order process was great and it shipped immediately. I knew I was in trouble when I measured the new diode and it too was open in both directions. It was easy to install but unfortunately no joy - did not solve the problem. At this point it is likely cheaper just to buy a new one
Parts Used:
-
Gregg from Santa Ana, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
42 of 81 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!