CVG2420B Jenn-Air Cooktop - Instructions

After I bought this part, installed it and the clicking still did not stop I finally found the problem. If your ignitor can still click then it's still good. The problem is the electric connection between the head burners and the base burners (Top Assembly diagram). Put a little weight on the head burner while grabbing it with your hand and grind it into the base burner with a little twisting motion. Repeat for all 4 burners. Presto! (you could be more professional and use steel wool or sandpaper to.)
If you stll want to know how to install this part begin by removing the control panel bracket #24. Then remove the glass top w/seal #9 (after removing the knobs). You may have to tease this out because the rubber seal is sticky. The switch plate #14 comes off after removing 2 obvious screws at each end and 2 not-so-obvious star screws attaching it to the manifold #6. Remove the spark module by removing 2 of the 3 screws and sliding it out of the 3rd screw.

Lift off blower vent cover. Lift out old filter. Clean walls and bottom of down draft using degrease soap and warm water. Dry. Discovered my grease filter will not install diagonally as shown in unit manual. Decided to drop into downdraft and put in front of fan suction. Found this left a gap at the top of fan suction that was not covered by the filter. Cut piece of wood 1 inch thick and width and length to drop down in the downdraft and lay on bottom. Set filter on top of wood in front of the fan suction. Verified that fan suction would pull filter tight against the opening by turning fan on and off. Put vent cover back over downdraft and told wife I was done.

I removed the center vent and inserted the filter...easy as pie...I went to your website and everything was there in an easy to follow way that even I could understand, my husband was totally impressed that I took care of it on my own....silly man.....it was so easy and delivery was extremely quick....so simple....thank you for making it so!!!!

Replaced the filter which required no tools.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

The entire cooktop had to be removed and taken apart to replace fan switch. I am thankful that this replacement part was available (slightly different than original part) through PartSelect.com since my local appliance parts store told me the part was no longer available.

I merely lifted the downdraft cover and inserted the new screen as
directed. THANK YOU FOR YOUR PROMPT RESPONSE TO MY ORDER.

Ordered a replacement grease filter.

Just needed to replace a scratched up grill on my stove top. The black paint was scratched off and looked horrible. You site made it very easy to find what I needed and it got here in two days. If I had known it was going to be that quick and easy, I would've done it a long time ago! Thanks!

Just placed new filter in slot

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

Took the old one out, plopped the new one in.

very easy slip in

I carefully removed the disgusting old filter and took straight to trash. I then used my wet/dry vacuum to clean the rest of the loose debris from the area where the filter area is located. I used a clean, dry cloth to wipe the remainder of the material away and then carefully lowered the clean new filter down into it's new home. So easy, it took longer to type out these directions :)

The old grease filter was removed and the entire downdraft was cleaned. The new filter was slipped in. It is so nice to have the old one out. I am so appreciative of finding this part. :-)